# How to develop a Truncated Cone

Follow these instructions below to develop a truncated cone. A truncated cone is a conical shape which has had it's top cut off at an angle. Sometimes you might need to develop these truncated cones as duct elements. Developing a truncated cone can be difficult but as long as you understand the concept of 'True Length Line' then this development will be easy for you.

Firstly begin by drawing your truncated cone elevation as shown above. Once you have your elevation you should draw your plan view (or top view). I have produced my plan view underneath the elevation.

You need to divide your plan view up into equal segments and then transfer these points to the elevation (as I have shown above).

Now you need to draw your end elevation (or side view) of the truncated cone. You need to do this to help produce your points that will assist in your truncated cone development. I have started my end elevation in the drawing above.

Once again you need to divide your end elevation up into equal distances, the same equal distances that you divided your elevation into (as shown above).

As per the detail above you now need to project the intersection points of these divisions to your truncated cut edge across to your end elevation and down (or up) to your plan view. These projected lines need to intersect with the corresponding divisions in the plan and end elevation.

In the end elevation I have drawn in the oval shape of the truncation.

From the end elevation you can project the two outside points of the plan view truncation. To do this you can use a 45 degree line like I have shown above.

In the diagram above the compass is set along the 'True Length Line' edge. In the diagram below I have projected this edge to the tip of the cone (if the cone were a complete shape).

Now this is the tricky part of truncated cone deveolpment. You need to project the top of the truncated line in the plan view to the centre line of the plan view. This line is then projected up (or down) to the true length line in the elevation. I have shown the true length line in red in the elevation. Now using your compass take this true length line and scrib an arc onto your development.

I have shown this method below for all the divisions of the plan view to generate each true length line. If you scroll down to the development you well see that I have scribed every true length line below. (If you are having trouble understand me with this particular instruction i'll try to develop this hub an explain better - like a work in progress, please send me an email or drop a comment below)

Below its the generation of the development. Start by creating a circle from the distance of the apex of the cone to the base along the true length line (or the edge of the cone in the elevation view). Then breack up the circle into equal parts, the same equal parts that you divided your plan view into. See below:

Below I have just tidied up the view by drawing lines from the division to the apex of the cone.

Below is showing how you transfer your true length lines to these cone divisions, with a cone you can use the same true length line twice around the centre line of the cone (centre line is shown darker)

Draw a curve between these true length line arcs, as shown below, now you can tidy up the development and you will have the development of a truncated cone.

Below are two developments of a truncated cone, both are correct. One shows the develoment join with the longest edge and one shows the development join with the shortest edge. If you are welding steel to make a duct element then you should use and start your development with the shortest edge as this is the most economical method of fabrication.

**Let me know if find these instructions helpful and please have a look at my other geometry hubs:**

- How to divide an obtuse angle into 4 equal parts:

How to divide an obtuse angle into four equal parts. - How to develop a Pyramid

How to develop a flat pattern of a pyramid in simple, graphical steps. - How to Develop a Cone - Cone Development

How to develop a cone or how to create a flat pattern of a cone can be achieved in a few easy geometrical steps. The geometrical method shown below does however have inaccuracy, so at the end of this hub I have included a mathematical formula to...

## More by this Author

- 3
How to divide an obtuse angle into four equal parts.

- 48
How to develop a cone or how to create a flat pattern of a cone can be achieved in a few easy geometrical steps. The geometrical method shown below does however have inaccuracy, so at the end of this hub I have included...

- 18
The purpose of this website its to provide you with extra information which I believe will be helpful to anyone interested in camping at Noah Beach Campgrounds.

## Comments 5 comments

what will be the surface if cut by section plane inclined at 30degree to horizontal plane

hi there,your methods are great and easy to understand.just checking if you have any formulas for developing rectangular shape to round.

regards

Wow! that's good hub. Keep it up.

super super

5