HOW TO  ASSEMBLE  COMPUTERS

1.    TO COLLECT ALL INFORMATION OF P4 P.C.

2.     PURCHASE GOOD QUALITY PRODUCT OR ORIGINAL PACKED PRODUCT.

3.    IF YOU DO NOT KNOW ABOUT ASSEMBLE  P4 ASSEMBLED OR INSTALATION.

4.    THE COMPUTER ASSEMBLED AT CLOSE ROOM AND NON POLLUTING AREAS.

5.    TO LEARN MOTHER BOARD MANNUAL BEFORE ASSEMBLED COMPUTER OR SET JUMPER SETTING.

PROCEDURE OF ASSEMBLING

 

1.    OPEN C.P.U. CABINET.

2.    OPEN A TEAN BOARD WITH SCREWS

3.    TO REMOVE SCREWS AND PLASTIC HOOK FROM A PACKET.

4.    TIET A MOTHER BOARD ON THE TEAN BOARD, WHERE KEYBOARD CONNECTER POSITION AS LIKE BACK SIDE OF THE CABINET.

5.    AFTER THIS PROCESSING, WE TIET C.P.U. WITH 370 OR 374 PINS AS REQUIRED MOTHER BOARD WITH THE HELP OF C.P.U. SOCKET AND LOCK

6.    AFTER THIS PROCESSING WE TIET THE C.P.U. FAN ON THE C.P.U. AND CONNECTING C.P.U. FAN ELECTRICITY CABLE.

7.    AFTER THIS PROCESSING CONNECT RAM WITH SD-RAM, DDR,

8.    AFTER THIS PROCESSING CONNECT SMPS WITH THE UP SIDE OF CABINET WHERE PLUG SYSTEM OUT SIDE OF THE CABINET.

9.    AFTER THIS PROCESSING CONNECT TWO CABLE BLACK-TO-BLACK 6 PIN EACH WITH MOTHER BOARD (IF AT CABINET) IF USED ATX CABINET THEN CONNECT 20 , 24 CABLE WITH THE MOTHER BOARD.

10.                       AFTER THIS PROCESSING CONNECT CARD ON PCI SLOT AS LIKE DISPLAY CARD, SOUND CARD, MODEM CARD, TV-TUNER CARD ETC. (WHERE CABLE AREA OUT SIDE OF CABINET).

11.                       CONNECT CD-ROM ON BAY AT THE FRONT PANNEL SIDE OF THE CABINET.

12.                       CONNECT F.D.D. (FLOPPY DISK DRIVE) ON BAY AT THE FRONT PANNEL SIDE.

13.                       CONNECT H.D.D. (HARD DISK DRIVE) IN THE BAY AT THE INSIDE OF THE CABINET.

14.                         CONNECT 4 PIN SMPS POWER CONNECTOR WITH THE H.D.D, CD-ROM OR WRITER, F.D.D.

15.                       CONNECT 40 PINS DATACABLE MOTHER BOARD TO H.D.D. AND CD-ROM RED CABLE TO RED CABLE TO ATTACH.

16.                       CONNECT 35 PINS DATA CABLE TO MOTHER BOARD TO FDD.

17.                       TO CHECK THE MOTHER BOARD JUMPER SETTINGS.

18.                       CONNECT CABINET LIGHT CABLES WITH MOTHER BOARD AS LIKE :- POWER LIGHT, PW POWER, HDD LIGHT,RESET CABLE, TURBO CABLE.

19.                       CONNECT CD-ROM SOUND CABLE WITH THE MOTHER BOARD.

20.                       CHECK THE ALL CABLE AND AGAIN TIET IT.

21.                       CLOSE THE CABINET COVER WITH THE SOME SCREWS.

22.                       CONNECT BACK SIDE CABLE OF CABINET AS LIKE  A POWER MONITOR, POWER, KEYBOARD, MOUSE, PRINTERPORT, USB CABLE AND MONITOR DISPLAY CABLE.

23.                       CONNECT YOUR 230 VOLTS CVT (CONSTANT VOLTAGE TRANSFORMER) OR UPS (UNURIPTTED POWER SUPPLY) AS PER REQUIRED.

24.                       ON THE POWER AND POWER SWITCH AT THE FRONT SIDE OF THE CABINET.

25.                       AFTER THE DISPLAY PRESSDEL. KEY THEN DISPLAY CMOS (COMPLEMENTARY METAL OXIDE SEMICONDUCTOR) ON THE SCREEN.

26.                       SLECT (IDE HDD AUTO DETECTION) OPTION AND PRESS ENTER KEY.

27.                       CHECK (STANDARD CMOS SETUP) IN WHICH FDD SETTING AND VIRUS SETTING.

28.                       CHECK COLOUR AND OTHER SETTINGS AS PER REQUIRED.

29.                       SLECT (SAVE AND EXIT SETUP) OPTION