Converting From Oil to Electric Heat

Oil Furnace
Oil Furnace

Skill Moderate
Things You'll Need Channel locks

5 gallon buckets

Screwdriver

Furniture dolly


Converting from one heat source to another can be a daunting process. With all of the choices out there, it can be hard to choose especially if you have an oil furnace. Switching from oil heat to any other requires the removal of the oil furnace. One of the easiest heat source transitions from oil heat is to electric heat. You will notice this system is a lot quieter and does not require ventilation as nothing is burned.

Step 1

Close the pump valve behind the oil pump on the tank. Turn the pump connector counterclockwise at the pump and valve junction. Unscrew to pump and set it to the side.

Step 2

Attach an old garden hose that is cut off to be a few feet long to the nozzle where the pump was attached and put the end of the hose in a 5 gallon bucket. Open the valve slowly and fill up about 3/4 of the way full and close the valve. Repeat this process until the tank is empty. Take the buckets to your local waste management facility for proper disposal. If you have a large amount of oil left, call the supplier who delivers the oil. They may pump it out free of charge.

Step 3

Remove the old lines by turning the connectors counter clockwise with channel locks. If there is any oil left in the lines, drain them out in a 5 gallon bucket. Take the lines and throw them in the garbage.

Step 4

Disconnect the exhaust pipe and barometric damper by removing the screws that hold the pipe to the oil furnace. Disconnect the exhaust pipe from the chimney by removing the screws and twisting. The entire pipe should come free. Set the pipe to the side for now.

Step 5

Remove all of the screws that attach the supply and return duct work to the furnace. Do not worry about disconnecting the power and the thermostat wires. This will be performed by the heating and cooling specialists later.

Step 6

Go to your electrical panel. Open the door to see the breakers. You will need two unoccupied slots for the breaker for the new electric furnace. If there are not two slots available or you have an older fuse panel, you will have to have an electrician install a sub panel prior to the new furnace being installed.

Step 7

After the HVAC contractor removes the power and the thermostat, remove the oil furnace with a furniture dolly. This will make it easier to get up the stairs. Help the HVAC contractor carry the much lighter electric furnace into the basement. From there you simply let them do their job. They should have the new furnace hooked up in a few hours.

Tips


When removing an oil furnace, have the HVAC contractor dispose of the unit. These units can cost extra to dispose of at a waster management facility.
Wear gloves to protect your hands from sharp duct work.
Warnings
In some jurisdictions, you are required to remove and abandoned oil tank. You usually have to cut the tank into pieces to remove it.
Never dump oil down your drains. Oil will harden in the plumbing traps and cause major problems with clogging and back ups.
If you smell something burning when you first use the electric furnace, this is the oil used in the manufacturing process burning off the heat exchanger coils. This is normal and will go away after a few uses.
Reference

Resource

For more information on home heating and saving energy, click here.

More by this Author

  • Building Paper vs. House Wrap- Which One is Better?
    4

    There has been a debate about this for as long as I can remember. What product works better? Good old fashioned tar paper or house wrap materials like Tyvek produced by DuPont? Well that depends. House Wrap The most...

  • Flat Roof Decks
    0

    Flat roofs with easy access are great for creating an outdoor living space. One issue that many people question me about is how to create a deck that is functional without compromising the waterproof roof surface. The...

  • Insulating A Flat Roof
    36

    Flat roofs have been a daunting task for contractors and homeowners alike since they were invented. They are hard to waterproof, hard to maintain, and hard to insulate. For today's purposes, we will stick with the...


Comments 1 comment

shanel profile image

shanel 6 years ago from Seattle

I don't know if I would ever attempt this conversion on my own, but your instructions are so detailed and clear it looks entirely possible. Very informative hub.

    Sign in or sign up and post using a HubPages Network account.

    0 of 8192 characters used
    Post Comment

    No HTML is allowed in comments, but URLs will be hyperlinked. Comments are not for promoting your articles or other sites.


    Click to Rate This Article
    working