How to Install Floating Wood Floors

Installing Floating Hardwood Floors
Installing Floating Hardwood Floors | Source

A D.I.Y. installation of floating hardwood floors is not that difficult or challenging, as long as you read and stick to the flooring manufacturers manuals and instructions.

The first thing to note is that different types of wooden floors require different systems of installations and these explicit details can be found in the mentioned manuals.

In any D.I.Y. project it is imperative that the step by step instructions must be read and assimilated carefully so as to ensure a well laid and beautiful floating hardwood floor finish.

Preparation of the sub floor that will receive the hardwood floor strips is crucial, and can make the whole D.I.Y. task successful or turn out a failure.

As the wood strips are not being attached to the sub floor, floating hardwood floors can be installed over almost any kind of floor base.

Preparations

To prepare for installation of floating hardwood floors, the following must be done:

  1. The sub floor must be very clean and dust free.
  2. The floor must be very even, without any humps, bumps, or crevices.
  3. Deciding on the direction in which to lay the floating hardwood floor.
  4. Make sure that the space between the finished hardwood floor and the sub floor is no more than three quarters of an inch (18mm).
  5. Gathering the tools required to complete the D.I.Y. flooring job.

DIY Installation Steps
DIY Installation Steps | Source

Woodworking Tools Required for Installation

To install floating hardwood floors, the general tools required are:

  • Woodworkers glue
  • Spacers
  • A hand saw, or a jigsaw
  • A ruler
  • Straps
  • A hammer
  • Chalk
  • A tapping block
  • A pull tool

Installers will need to check the manufacturers detailed instructions to know if any additional tools are required.

All these tools can be bought at any home improvement, D.I.Y. stores or online at eBay.


Articles:

Bamboo Wood Floors

Antique Oriental Carpets and Fine Rugs


Installation Process for Floating Wood Floors

First test the floor to see if it’s even and level. This can be done by laying a plank of wood at the edge (of the floor).

If there is any space between the wood and the sub floor that's more than 3/4 of an inch (18mm), spread some self-levelling joint compound on the floor.

When the compound dries, your sub floor should be adequately level and you are ready to proceed.

The most important rows while installing floating hardwood floors planks are the first 3 or 4 rows. If these rows are not straight from the start, you may as well know that as you proceed along the lines become less and less straight, and the installed planks will start to open up as you tap the next planks into position.

The planks should be straight and all the joints should fit snugly, using clamps and straps to keep all the connections tight.

Now start to attach the floating flooring planks by using an adhesive between the joints of the wood planks. To apply the glue, run a bead of glue along the joint of the wood, and then snap that piece into the first piece you've already set down.

The glue dries in roughly ten minutes so you want to be clear on placement of the wood before placing the glue along the joints. Be careful, and do not to use excessive glue.

During installation of floating hardwood floors, it is a great idea to measure at least 2 times, so you don’t end up with too many off-cuts or pieces that will become useless scraps of hardwood.

While inserting each plank, fit the pieces together using a hammer, and tap it gently with a tapping block. Knock very gently to close the gaps. It's better to knock often, but softly, than it is to knock a few times with force. There shouldn't be any gaps between planks while installing floating hardwood floors.

Always drive in the joint directions that you are trying to close because once the pieces are set and dry, it will be virtually impossible to adjust the joints.

DIY or Hire a Woodworker for Installations

WILL YOU PREFER DIY FLOATING HARDWOOD FLOORS INSTALLATIONS, OR WOULD TO HIRE SOMEONE TO DO IT FOR YOU INSTEAD?

  • YES I PREFER TO DO IT MYSELF
  • NO, I'LL MAKE A MESS OF IT, SO I'LL HIRE
See results without voting

Effects of Weather on Floating Floors

As you lay along, you must leave a bit of space around the perimeter of the room to allow for contraction and expansion that occurs occasionally during weather changes, because wood changes with time and temperature.

Towards the end of your floating hardwood floor installation task, the space left will need your pulling iron and the hammer to draw the planks together. For larger areas, it is suggested to allow as much expansion area as is possible.

After completing the installation of floating hardwood floors, you must fit in your base moldings or skirting, transitions and trims to cover the spaces left at the edges for expansion. Then leave the floor to set as advised in the manufacturer’s instructions.

© 2009 viryabo

More by this Author


Comments

No comments yet.

    Sign in or sign up and post using a HubPages Network account.

    0 of 8192 characters used
    Post Comment

    No HTML is allowed in comments, but URLs will be hyperlinked. Comments are not for promoting your articles or other sites.


    Click to Rate This Article
    working