How to Replace a Kitchen Sink Sprayer Hose

How to Replace a Spray Attachment

When the old rubber band around the sprayer hose trick fails to expel enough water to hit your target, bringing with it the familiar soggy-squeal, it is time to replace that old Sprayer Hose and right now! Yep, when stopgap measures fail time and time again, you will need to replace the entire sprayer assembly. Your first thought may be to give a local low cost plumber a call, but wait a minute and think this through. What if you decided to be your own cheap plumber? You would incur the cost of parts, sure, but no labor cost; and that's the way to go! Replacing a sprayer hose is easy and takes just a few minutes and very little know-how. Stick with me, and see just how much you can save by NOT paying one plumbing bill too many.

Replacing a Kitchen Sprayer Hose is Made Easy Using These 3 Simple Steps.
Replacing a Kitchen Sprayer Hose is Made Easy Using These 3 Simple Steps. | Source

Before Going to the Trouble of Replacing the Sprayer Hose

A Mineral Build-up on the Spray Nozzle may be the cause of the faulty sprayer results. Before you replace the sprayer hose, try soaking the head of the sprayer (nozzle) in a bowl of warm vinegar to dissolve any calcified minerals that may be causing the blockage. This should enable the nozzle to work properly; if it does not, proceed with replacing the entire assembly.

Note: There will come a time when you have to determine if the hose assembly is simply too old to continue clearing the mineral deposits. Sometime it's just better for those who use the device frequently to replace the fixture for the sake of daily convenience.

Stuff You Need for the Job

  • Screwdriver
  • Pliers
  • Adjustable wrench
  • Sprayer replacement kit

Approximate time needed: 40 minutes

The Best Way to Replace a Kitchen Sink Spray Attachment

For the best results, purchase a replacement assembly that is made by the same manufacturer of your faucet, but universal kits will also work. It only takes three really simple steps to replace the old sprayer hose: Remove the old assembly, Install the new deck fitting, and Get the new hose in place.

If you are unfamiliar with the terms used here, refer to the diagrams inset below for part labeling (names).

  1. Removing the old assembly;Start by turning off the water and draining the hose as much as you can. Then, reach under the sink and literally cut the old sprayer hose in two—be prepared to catch the little bit of water that will drain out. Pull the old hose through the deck fitting, and throw it away. Next, from under the sink, unscrew the remaining length of hose from the faucet nipple. Remove the old jamp nut from the deck fitting under the sink, and then simply remove the fitting.
  2. Install the new deck fitting; Now that you have removed the old sink sprayer assembly, install the new deck fitting, and then feed the hose through it from above.
  3. Get the new hose in place; Be sure to apply a little bit of pipe joint compound to the male threads of the faucet nipple, and thread the new hose in place using an adjustable wrench (I recommend using a smooth-jaw pliers to avoid any potential rips or tearing of the new hose assembly).

AVOID OVERTIGHTENING THE FITTING AT ALL COST!

In case you have never heard of the sprayer hose rubber band prank...

STEP #1

After removing the old spray attachment, slide the rubber gasket onto the new one's fitting shank, and feed the shank through the sink deck hole.

Step #1 in your Cheap Plumber Kitchen Sprayer Replacement Project
Step #1 in your Cheap Plumber Kitchen Sprayer Replacement Project | Source

STEP #2

Slide the hose through the deck fitting from above, and install the jamp nut below. Tighten the nut until it is snug.

Step #2 in your Cheap Plumber Kitchen Sprayer Replacement Project
Step #2 in your Cheap Plumber Kitchen Sprayer Replacement Project | Source

STEP #3

Finish the repair by connecting the spray attachment's hose to the faucet's diverter nipple. Use a light coating of pipe joint compound on the niple.

Step #3 in your Cheap Plumber Kitchen Sprayer Replacement Project
Step #3 in your Cheap Plumber Kitchen Sprayer Replacement Project | Source

Now that the Sprayer Hose has been replaced...

With the new sprayer hose installed and working great, the next step is to find the perfect rubber band to twist around the nozzle. Be sure to wrap the band snugly so it holds the sprayer button down fully. Next, stand by for someone to turn the sink water on, and enjoy the show. This might be a good opportunity to create your own "Rubber Band Sprayer Prank" video!

Happy Plumbing!

Conversion Chart From USA to Metric Measurements

(click column header to sort results)
TO CONVERT:   
TO:   
MULIPLY BY:  
Inches 
Millimeters 
25.4 
Inches
Centimeters
25.4
Feet 
Meters 
0.305 
Yards 
Meters 
0.914 
Square inches
Square centimeters
6.45
Square feet
Square meters
0.093
Square yards
Square meters
0.836
Cubic inches
Cubic centimeters
16.4
Cubic feet
Cubic meters
0.0283
Cubic yards
Cubic meters
0.765
Ounces
Millimeters
30.0
Pints (U.S.)
Liters
0.473 (Imp. 0.568)
Quarts (U.S.)
Liters
0.946 (Imp. 1.136)
Gallons (U.S.)
Liters
3.785 (Imp. 4.546)
Ounces
Grams
28.4
Pounds
Kilograms
0.454

HANDY ONLINE PLUMBING RESOURCES

More by this Author


Comments for "How to Replace a Kitchen Sprayer Hose to and Your Own Cheap Plumber" 8 comments

Green Dog VT profile image

Green Dog VT 4 years ago from chester,vt

Great hub easy to understand and the pictures are the best part of understanding and how to fix the hose step by step. Thanks for great easy to fallow directions


K9keystrokes profile image

K9keystrokes 5 years ago from Northern, California Author

AEvans~ I hope that bookmarking this will help when you decide to replace that sink sprayer hose of yours. I really appreciate your stoping by today! Thanks for the comments.

HubHugs~

K9


AEvans profile image

AEvans 5 years ago from SomeWhere Out There

Looks simple enough and I am bookmarking this to. I believe ours is almost ready to be replaced. Thanks for the info! :)


K9keystrokes profile image

K9keystrokes 5 years ago from Northern, California Author

Cardisa~ LOL! How funny. Ya gotta' love those helpful friends...Thank you for your comments on the old kitchen plumbing. I hope nothing too awful happened during your plumbing repairs!

HubHugs!

K9


Cardisa profile image

Cardisa 5 years ago from Jamaica

I wish I had hired you to do my plumbing instead of my boyfriend's friend, it would have saved a lot of trouble...

Nice guide.


K9keystrokes profile image

K9keystrokes 5 years ago from Northern, California Author

livelonger~So happy to see you made it by today! How cool that you feel your old sprayer hose has lost its grip on your kitchen! I hope the project goes smoothly and makes for many rubber band sprayer pranks in your future. I appreciate your remarks!

Huge HubHugs~

K9

Simone~ Using a bowl of warm vinegar is a great way to get that final mileage out of a mineral crusted sink sprayer without ANY hassle. Thank you for your comments and Happy Plumbing!

HubHugs of course!

K9


Simone Smith profile image

Simone Smith 5 years ago from San Francisco

Another great guide! I love the tip about soaking the hose in warm vinegar first- I'll have to give that a try!


livelonger profile image

livelonger 5 years ago from San Francisco

Wow. This is yet another shockingly good, and eminently useful, Hub. We have a kitchen sink with an old, yellowed sprayer hose that is still functional but a bit of an eyesore. We had hesitating on replacing it, because it still works and we thought replacing it would be a PITA. Now we know it will take us about 40 minutes and a bit of elbow grease, but these instructions will set our minds at ease. :) Thank you!

Submit a Comment
New comments are not being accepted on this article at this time.
Click to Rate This Article
working