How to make an inexpensive umbrella stand
Home Made Umbrella Stand
When it comes to umbrella stands, heavy is KING!
Have you ever bought an umbrella stand for around $20 at the grocery store, only to have your umbrella tip the stand over at the first little gust that comes along?
If you pick up those stands, they only weigh about 10 or 15 pounds. Not exactly iron! Then if you go to a home improvement store or boutique shop, they want $50 or $100 for a marble or iron stand. These stands look nice, but when you need several of them, cost is major factor.
Here's my method, use your imagination and see if you can expand on what I've done. Total time from start to finish (without waiting for paint to dry) about 30 minutes. This is an easy project anyone should be able to do. Just be sure you get help if you can't lift a 60# bag of concrete.
Step 1. Get your materials
You will need:
- 5 Gallon bucket or a 5 Gallon plant pot (plastic) $3.00
- Length of 2.5" Schedule 40 Rigid PVC conduit UV protected $10 for 8 feet
- 60# bag of concrete or cement. What ever is cheapest. $3-$4
- Can of plastics outdoor spray primer $3-$5
- Metal tape measure
- Hacksaw or electric sawzall with a fine blade
- Plastic sandwich/snack bag
- Sharpie pen
- Large bin or wheelbarrow to mix the concrete in
- A small level
- 2x4 board about 2-3' in length
You probably won't be able to buy the PVC in short lengths, so you will get enough to make several umbrella stands
Step 2. Paint the bucket(s)
If you choose to, paint the outside of the bucket, what ever color you want using the spray primer. If you want, go over the primer with a spray paint too. I chose to use a clay red primer which matches my patio furniture. Let it dry an hour or two before you use
Step 3. Cut the PVC to length.
I chose 20" since it would be about 3/4 or more in the concrete but still have some more to support the umbrella. Cut yours to what ever length you want, but I would recommend that it is at least the height of the bucket.
Be sure to cut the PVC as straight as possible. This will ensure that the umbrella will be as plumb as possible when it sits in the stand. You may want to paint the PVC as well at this point.
Step 4. Prepare to make the stand.
Put the sandwich bag over one end of the PVC, this will prevent concrete from getting into the tube. Place the PVC in the center of bucket with the bag at the bottom (you will bury the bag).
Next, mix the concrete as the directions say. I used a wheelbarrow, you could use a small tub, just something big enough to mix the materials with water and be able scoop it out. Add a small amount of water at time while you mix it, you want the concrete to just barely be moist, no need to make it into mud. Mix it with a shovel. It should be like wet clay.
Step 5. Put it together.
You may find it easy to have another person present to hold the PVC level and straight while you put the concrete in. Start shoveling the concrete mix around the PVC, be sure not to get concrete down in the PVC. Use the 2x4 board to tamp around the PVC to get rid of any spaces. Use the level to make sure the PVC is straight up and down. Fill it up as much as you want, get it as close the top of the bucket as you can. You will probably end up with 50-60# of concrete in the bucket.
- You may want to use a small square of wood to smooth out the surface of the concrete.
- You may use broken tile or marbles or rocks to cover the surface of the concrete. Just do this before the material sets.
- Instead of using a 5 gallon bucket, try a 5 gallon plant pot or build a frame out of 2x4 and ply-wood. The wider the base, the more stable this umbrella stand will be. You could put heavy casters on the bottom to make it easy to move around.
Step 6. Finishing touches.
Using a wet rag, clean up the spilled concrete on the bucket, get it nice and clean. If your wife thinks this bucket it ugly (like mine does), then get some stencils and put a nice design on the out side of the bucket.
I would suggest, not carrying the bucket by the handle, the handle will break. In my next rendition, I think I will get some re-bar and make some handles that go all the way through the bucket from side to side. This way the concrete will hold the re-bar in place and I could lift the stand if need be.
Besides having to buy an 8 foot piece of PVC, the rest of the materials are pretty cheap. You could build one of these stands for around $10. I probably spent about $30-$40 on everything, but I bought enough to make 3 stands and I still have enough PVC to make about 3 or 4 more stands.
I hope I gave you some ideas, don't be afraid to work with concrete in this fashion, you're not going for strength, you're going for weight. Be creative and don't settle for what's in the store any more!
More by this Author
I'm a 36 year old man. I've been married 9 years and I have 2 children, ages 3 and 5. My wife was having issues with the pill. Like most women she'd been on birth control since about the age of 17. All those hormones...