How to Use a 400-1000 MHz Log Periodic Printed Circuit Board Antenna

A 400-1000 MHz LP antenna by Kent Electronics and WA5VJB
A 400-1000 MHz LP antenna by Kent Electronics and WA5VJB | Source

How can you use a 400-1000 MHz log periodic printed circuit board antenna?

The log periodic printed circuit board antenna or LP PCB antennas in the 400 to 1000 MHz frequency range have a variety of uses, only a few of which fall under FCC rules.

The 400-1000 MHz log periodic antenna can be used for Ultra High Frequency or UHF HDTV signal reception. These antennas are regularly used for wireless microphone applications, scanners and wireless LANs. The Kent Electronics brand 400-1000 MHz LP antennas were used on the set of Avatar for picking up wireless microphone signals.

Glue a piece of wood or fiberglass to the back edge of the antenna then drill that for a microphone stand to be able to attach it to a pole without affecting its signal reception.

Log periodic PCBs in the 400-1000 MHz range can be used as feeding reflector antennas. If you are a ham radio operator, these PCB antennas work well on the 70 centimeter ham band and dual band radios. These antennas may be used in VHF/UHF utility monitoring and RF measurements in the field.

This design can be used for both transmission and reception. The trapezoidal printed circuit board concentrates the beam into a signal four times as powerful when used in broadcasting.

How do you mount a log periodic printed circuit board antenna?

The PCB footprint is for the standard SMA connector. Either a straight or 90 degree right angle can be used to mount this antenna. However, the connector should be on the side with the larger ground area.

You can also solder coax directly to the antenna if you like, though coax should be routed along the boom of the antenna. Cutting the embedded element affects its performance.

You can drill mounting holes through the fiberglass between the elements on the antenna. The best place to attach a mount is the back-center area of the log periodic printed circuit board antenna. Wood, sheet plastic, and most any non-metallic material can be used as mounting. Don't attach it to a metal mount, since this alters its performance. Then you can have your bracket attached to the wood or plastic.

The antenna works with frequencies down to 400 MHz. If you are only using channels above 500 MHz, then you can sacrifice the longest element by drilling through it when mounting the antenna. For example, those working on the set of the movie Avatar just drilled holes in the longest element and mounted Kent Electronics 400-1000 MHz antennas at that point. Doing this messes up reception in the 400 to 500 MHz range, but not higher frequencies of 500 MHz to 1000 MHz / 1 GHz.

Antenna Factors for 400-1000 MHz LP PCB Antennas

Frequency
Antenna Factor
400 MHz
18.8
450 MHz
17.7
500 MHz
18.2
600 MHz
19.8
700 MHz
21.2
800 MHz
22.3
900 MHz
23.3
1000 MHz/1 GHz
24.2
1050 MHz
24.7

Can you apply a protective paint to these antennas?

You can paint Kent Electronics 400-1000 MHz LP PCB antennas black or another color. The brand and type of paint makes no difference. The metallic paints are not electrically conductive, shiny, but not conducting. Use enough paint to get the desired color, but no more.

Paint changes the frequency of the antenna a little bit. So the 400-1000 MHz becomes 390-980 MHz, but still works fine with wireless microphones, for example.

Some users have had limited success dipping them in plastic coatings, but this is not recommended by the manufacturer.

Are there any limitations to using 400-1000 MHz PCB antennas?

If you want to use a 400-1000 MHz PCB antenna as a signal booster for your cell phone, know that you need the consent of your cell phone service provider to do so, and not all providers allow you to do so. While signal reception rarely runs afoul of the law, the FCC limits signal broadcasts in some cases, especially when it interferes with the communications of others or licensed broadcasters.

Note: If you use these antennas as a signal booster for your cell phone, the triangulation function used to locate where your cell phone is located when you place an emergency call may not work correctly.

More by this Author


No comments yet.

    0 of 8192 characters used
    Post Comment

    No HTML is allowed in comments, but URLs will be hyperlinked. Comments are not for promoting your articles or other sites.


    Click to Rate This Article
    working