Colorblocking Clothes in Crochet: How to Change Colors
The colorblocking trend has been around for quite some time. As I was browsing through Ravelry one day, I saw this colorblocked dress in the forums made by watbetty. While I haven't had enough experience then, I have since made my own Colorblocked Panel Sheath Dress.
This hub is a tutorial on how to do colorblocking by carrying the colors not in use at the wrong side of the work and introducing new colors only when it starts in the pattern. Included are some pictures on how to do it.
Jacquard (or Tapestry) Crochet
Jacquard (or Tapestry) crochet is just like regular crochet, only it involves having more than 1 yarn being carried at the back while one color is being used. Patterns for this kind of crochet are usually drawn in grid charts with each color represented by a color or a symbol filling in the square.
If you are right-handed, you read the chart from the bottom right corner, working your way across to the left side. If you are left-handed, do the opposite and start from the bottom left corner, working your way across to the right side.
Different Ways of Introducing New Color
When you want to change colors, you just do the normal stitch, but stop at the last part of the stitch and add the new color. For example, if you want to change colors at the end of a single crochet, do the normal stitch until you reach the final yarn over before drawing up all loops. Introduce the new color then, by yarning it over the hook and then pulling it through both loops on the hook.
- Adding the color when you need it and fastening it off when you change to the next color. This method will have no threads hanging at the wrong side because you can just work over the loose threads or weave in the ends to hide it. But this will be tedious because of all the weaving in you need to do once the project is done. However, this method is sometimes necessary when the next section for the color is too far away from the current stitch. If you do not fasten off, the thread hanging at the wrong side will be long and might snag during handling.
- Adding the color when you need it and pulling it up again when necessary.The main advantage of this is to conserve yarn and to reduce the ends in the project. The bad thing is, the wrong side of the work will have many hanging threads from where you pulled up the color for the next section. If you can keep the wrong side from showing, this is a good method. Also, if the colors are close together, it will save you the trouble of weaving in ends and fastening off every time you change color.
- Beginning the second color from the very start. This method involves crocheting over the second color right from the beginning stitch over the starting chain. This is done to make sure the gauge is consistent throughout the work. But, some of the secondary color will show from the very beginning. There is a tutorial for this in About.com if you are interested. The disadvantage of this is you need more thread than usual and will make the project heavier.
How to Change Colors
I will be showing the second method in this hub because a) I am using thread, so the gauge would not change so much compared to using yarn; and b) I am merely showing how to change colors while doing vertical stripes, so the hanging threads at the back is minimal as the colors are just continuously going up.
- Start the chain with the lightest color you plan to use. In this case, I used a light yellow. Start the stitches with the same color until you reach the point where you want to change the color.
- When you reach the last stitch of the current color, before you do the final yarn over and pulling through all loops, insert the new color as shown in the picture below. This new color will be the thread you will yarn over and pulling through all hooks.
- As you can see from the photo above, there are three floating threads. Take the first color and make sure you put it at the back (the wrong side of the work). Continue with the pattern, making sure that you stitch over the end of the new color to hide it.
- In order to make blocks, you have to continue using the same colors for the next rows. Always make sure that the threads are hanging at the wrong side of the work. When you need to change colors, just pull up the one you need and put aside the current color.
- Just continue the pattern in rows until you reach the desired length of the stripes.
How to Incorporate Colorblocking in Designs
You can do stripes, checkerboard patterns, designs in the middle of the project, etc. Just be creative and try colorblocking your favorite patterns.