ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel
  • »
  • Arts and Design»
  • Crafts & Handiwork

Making a Macrame Board

Updated on March 28, 2014

Making a macrame board for $15

If you enjoy macrame and don't have a macrame board you are in for a pleasant surprise. You can make your own board cheaply and easily. The board shown here will work much better than a clip board or a bulletin board and significantly better than safety pinning your working cord to your jeans.


You can purchase all of the required materials from a home improvement store.

The total cost of the materials: $6 for the foamular project panel, $4 for the drywall sanding sponge, $5 for the glue.

DIY Macrame Board
DIY Macrame Board

Gather your materials and tools

This project will require a few inexpensive supplies. All of these supplies can be purchased at a home improvement store (you may already have them in your garage or attic).

  • Insulation board which is at least 1.5" thick. I had some 2" board in the garage but you can purchase a "project board" from the store for about $6. The project board is only 1" thick so you will need to cut each piece twice and glue each piece to its twin (after doing this you should end up with 3 pieces of insulation board that are each 2" thick).
  • A straight edge ruler will allow you to accurately measure each piece.
  • Use a pencil to delineate your measurements. Measure each piece twice before cutting :)
  • A saw to cut through the insulation board. A jigsaw makes this easy but you can use a hand saw.
  • A sanding sponge to sand all the cut edges. This will prevent the insulation from shedding.
  • Glue holds all the pieces together. I use Gorilla Glue because it makes a very strong bond. When using Gorilla Glue remember that each side touching the glue needs to be slightly wet. Use this glue sparingly because it does expand.
  • Clamps will keep the pieces of the board aligned correctly as the glue dries and will ensure a tight bond. Clamps, vices, heavy books, all of these things will work as long as you are careful to ensure the correct placement of all the pieces before you apply pressure.

Making the pieces

Cut a piece of insulation board that is 16" long by 9" wide. Measure 2" down from the top of the 16" side and draw a line across the entire 9" width. Measure 2" below that line and draw another line. Cut each of the 2 inch pieces with a saw and sand the cut edges until they are smooth. This should leave you with a board that is 12"x9" and 2 pieces that are each 2"x9".

Making A Macrame Board

Start with a piece of insulation board that is 16 inches long by 9 inches wide.  Measure 2 inches from the top and draw a line, then draw another line 2 inches below that.
Start with a piece of insulation board that is 16 inches long by 9 inches wide. Measure 2 inches from the top and draw a line, then draw another line 2 inches below that.
Using a Jigsaw (or a coping saw, or any saw) cut the first 2 inch piece, then the second.
Using a Jigsaw (or a coping saw, or any saw) cut the first 2 inch piece, then the second.
Sand the edges of each piece of the board with a sponge sander.
Sand the edges of each piece of the board with a sponge sander.

Putting it together

Apply glue to the bottom of each 2"x9" piece and place them onto the top and bottom of the 9"x12" base (read the instructions on the glue for best results). After applying the glue check to ensure that each of the smaller pieces are flush with the edges of the base. Clamp the smaller pieces to the base using at least 1 clamp on each side.

Apply glue to the bottom of each 2"x9" piece.
Apply glue to the bottom of each 2"x9" piece.
Align the pieces and clamp them together while the glue dries.
Align the pieces and clamp them together while the glue dries.

Why use a macrame board

I have been a macrame hobbyist for the last 3 years. In the beginning I would safety pin my project to my jeans, I progressed to a clip board, then a loom. I wanted something that would hold both ends of the core cord and allow me some room to move the working cords over and under. I wanted a board which was able to hold the project with tension but still allow me to take the work off to add beads or remeasure. I began to shop around for something better and considered cork-board and hobby foam (polystyrene) but neither of them could hold up to the abuse of being pulled while holding tension. While walking through the hardware store I came upon insulation board and bought some to try it out. It held the T-pins securely which was a good sign. I put a project on the board that used heavy glass beads and lots of tight square knots, I put the core cord under high tension along the length of the board. As I began to work I was easily able to move the working cords above and below the core. I removed the project from the board and then put it back on using the same high tension and it held just as well as it had before I removed it. That was about a year ago and I have never looked back. I even made some 4" wide "travel" boards.

Macrame projects

This project wouldn't be possible for me without a macrame board.
This project wouldn't be possible for me without a macrame board.
Not even the cat can get the project off the board!
Not even the cat can get the project off the board!

Comments

    0 of 8192 characters used
    Post Comment

    • profile image

      Jacobb9205 2 years ago

      Looks awesome!