ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

How to reupholster a vehicle bench seat.

Updated on April 10, 2012

Getting Started.


If you have a bench seat that needs reupholstered, or you would like to learn on how it’s done than this is the place for you. It is actually a lot simpler than it looks, and you will have professional quality custom interior. I will teach you how to reupholster the bench seat from start to finish. You could have your friends and even strangers stop you in traffic to ask you one question….WHO DID YOUR INTERIOR? AND HOW MUCH DID IT COST?


The photos you will see here are from a 1983 Cutlass Calais, but many seats are similar especially in these older vehicles. You can use the same concepts on just about any seat you come by.

MATERIALS: Fabric (approx. 3.5 yards should do)

Heavy duty thread.

Eyelets. (Metal eyelets can be found at any craft store.)

Scissors.

Cloth measuring tape. (This is important to measure the curvature correctly.)

Ruler or yardstick.

Hammer.

Zip ties – or – Hog ties.


STEP 1


Remove the bench seat from the vehicle. The bottom portion of the seat in most vehicles can be very easy to remove, and should just pop right out. The top portion can be a little more difficult, it usually has a release point in the rear of the seat that may need to be loosened with a screwdriver. Once you remove the top and bottom portions of the seat the real fun begins!


STEP 2


Measuring your material. Using the cloth measuring tape measure the dimension of the seat both top and bottom portions may not be identical. This is the key step to make your seat look crisp and professional. I create a drawing of the seat, with the dimensions written, to refer back to when needed. Measure the front, and the sides. For this particular seat, I chose a blue marine vinyl fabric which is waterproof and has the traditional look of leather.


STEP 3


Cutting your material. Not so important to stay perfectly straight, save your energy. When you sew your edges together, that is what will make the crisp crease that is needed. After you have your material ready to go you may jump into creating you masterpiece.


STEP 4

Sewing pleats into the fabric. This is what makes a custom interior look really professional the PLEATS. Sewing pleats is fairly easy because you will be sewing straight lines. Chose how many pleats you would like, and space them evenly. On the back of the fabric with a ruler and pen you may draw lines to follow to ensure you lines are perfectly straight I chose to sew six pleats on each side with one inch in between, and larger pleats in the middle to accent them. I suggest doing the pleats on the top and bottom portions first to make sure they line up correctly with each other.


STEP 5


Sewing the pieces together. This is self-explanatory. You will sew your sides on to the main pleated pieces. Remember to make sure the fabric is facing the right direction when sewing them together. The corners can be tricky; you have to turn the material as you go.


STEP 6


Securing the edges. This is an important step to ensure your material will not rip when being stretched over the seat. I use a canvas material which is durable and can withstand more pressure. Cut Strips about 3.5 inches wide, and then fold the material over to double up the edges. Sew this edging along the bottoms of your main pieces.


STEP 7


Inserting Eyelets. This step is to also ensure that your seats will not rip. The metal eyelets are very easy to install. Around the canvas edging you will cut small x’s into the material and insert the eyelets. Personally I space the eyelets approximately 3 inches apart. These eyelets are very inexpensive and come with a tool to hammer them together. Once your eyelets are in your almost done!


STEP 8

Stretching the material. You may stretch the material over the seat like I did here, or you may completely remove the old material and replace with your own. On this cutlass I installed the new seat cover over top of the existing upholstery incase the car is sold and the owner would like to make it original. This step you may need a friend or assistant to help. You want to pull from opposite sides starting from the middle and working your way out. As you pull the material tight, start inserting the zip ties into the eyelets and securing them to the frame of the seat. Zip them tight and remove excess waste. Make sure the material is nice and snug fitting to smooth out any wrinkles.


THAT’S IT! HOPE YOU ENJOYED.


Source

Comments

    0 of 8192 characters used
    Post Comment

    No comments yet.