ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

Install a New Water Pump

Updated on March 23, 2016
Isn't it time we replaced that old water pump with....
Isn't it time we replaced that old water pump with....
...a brand New Water Pump!
...a brand New Water Pump!

Overheating?

If any of the following apply to your vehicle it may be time to replace the water pump.

It may be time to replace the water pump. Water pumps wear out. Just like any moving part they eventually wear out. The water pump is a critical part of your engine. It's the blood flowing through your engines veins, if the fluid leaks out....it dies.

The water pump is usually located front and center of the engine. It sits against the engine behind a pulley and the fan. There are "weep" holes located on the bottom and the top of the pump. These weep holes start to leak when the pump is wearing out. If left unreplaced eventually the bearings will wear out and the car will overheat which could cause major engine damage.

To my lady friends out there (I say ladies because, more often than not, we are the culprit of destroying an over heated engine, but this information applies to all) when the car overheats it means literally that your engine has become so hot the metal is breaking down, in other words, your engine is melting! You must stop the car and allow it to cool down or risk blowing your engine.

These are all signs of a water pump in need of replacement.

So, let's pull off those acrylic nails, pull our hair back and get started.

Where Is the Water Pump?

Below is a nice diagram of the location of the water pump on a standard v8 engine. On engines that are sometimes referred to as "sideways" the location would be on the side.

Source

Let's Head to the Auto Shop

The replacement of a water pump can take from 1.5 hours to 3 hours depending on your experience level. Experience matters only because there are several items that must be removed to access the water pump. Simple items, but time consuming to remove. If you're experienced than you're going to know exactly what needs to be removed and start pulling parts off left and right. If you're not experienced you're going to be looking about, reading your shop manual and being more cautious. Being cautious is good, just make sure you allot yourself enough time to complete this endeavor.

Let's head over to the nearest auto shop for a new pump. They run $50 - $80 for a normal, run-of-the-mill water pump. If you enjoy spending money I'm certain you can find a chrome plated one for several hundred, but for this hub we'll go with run-of-the-mill.

Be sure to have the make, model and year of your car with you when you head for the auto shop. Engine size and type is always a help too. Water pumps can vary depending on the size of your engine.

If you decide to use sealant or if the instructions in the box recommend sealant, by all means pick some up while you're there. The sealant should say right on the tube if it is good for high temperatures and if it will withstand constant water contact. These things are important because some sealant can't handle high heat or water and they will break down over time and that's NOT going to be good after all your work!

Tools for the job

Now that you have your new water pump its time to collect the tools we'll need to complete the job.

  • 10mm & 14mm wrenchs and sockets
  • tube of sealant (optional, I prefer it myself)
  • breaker bar or strong, long wrench to move tensioner
  • 5/8 socket for tensioner
  • new water pump
  • radiator fluid
  • catch basin for fluid
  • torque wrench (the mounting bolts need to be torqued down)

And that's it! Replacing the water pump doesn't require a lot of tools because many of the nuts and bolts require the same size.

Don't skip the torque wrench. It's a vital tool in this application. The torque wrench is placed on a nut or bolt and the mechanic (you are the mechanic now) twists the nut or bolt in a tightening fashion, the torque wrench indicates how tight that nut or bolt is. According to your particular vehicles specifications there will be a certain "poundage" or "inch pounds" you need to set on your nut or bolt. You do this by watching the needle on the torque wrench until it reaches the specified poundage, or inch pounds. When the needle is pointing to the number you want, you should be able to hold the torque wrench at that spot and the nut, or bolt, won't twist anymore. There are torque wrenches that you set the dial on it to what number you need and it automatically stops turning (it's clutch inside it) when you have tightened to that number. Torque wrenches are surprisingly expensive. Before dumping a bunch of money buying one, check out your local O'Reilly's. They rent out all kinds of tools. They may have a torque wrench to rent! If you return it, and it's in the same condition as when you took it, they give you your money back :)! You can't beat that!

Now back to why you need a torque wrench, if the bolts are not tightened evenly, then the weak bolt will begin to allow water to seep through, or the rotating of the engine can cause each bolt to loosen. The seeping water may even blow out your pump gasket. That would suck so lets make sure we have a torque wrench handy.

The video below is a "Still Shot Instructional Video" of a water pump replacement. The vehicle in the video is a 1989 (year), Chevrolet (make), Silverado 3500 (model), with a 454 (engine size).

Below the video are step-by-step instructions. Basically the same information as the video has but with a little more detail.

Still Shot Instructional - Replace Water Pump

Removing the Water Pump

  1. Disconnect the negative battery cable at the battery. This will prevent an accident electric shock.
  2. Now drain the radiator fluid by opening the radiator cap and unscrewing the draincock. The radiator cap is located on top of the radiator and the draincock is normally located on the opposite side of the radiator cap but on the bottom of the radiator. It will be facing toward the rear of the vehicle. You reach your hand down and unscrew the valve. It can be firm to twist. You may need to wedgy a pair of pliers down there to help get the valve started.

    Radiator fluid is highly toxic to pets. It is imperative that all radiator fluid is collected in a container and disposed of properly. Even the smallest amount of radiator fluid can poison your pets! There are collection centers listed in the phonebook that you can drop off your radiator fluid at.

  3. Remove the fan shroud. This is located at the front of the engine compartment. Its a piece of plastic that encircles the fan and attachs to the body of the vehicle. There are two to three screws (usually 10 millimeter) along the top of the shroud and four more halfway down the shroud. To find these screws halfway down, locate the end of the shroud and run your hand down the edge until you can feel a lip. The screws are through that lip into the lower part of the fan shroud holding them together. These screws are also 10 mm.
  4. Now its time to remove the serpentine belt. Its that long belt that winds through all those pulleys to keep everything running and in sync. Check the front edge of the engine compartment for the diagram showing how your belt should be routed if its not there, or unreadable, pull out your shop manual and look it up. Compare the picture in the shop manual to the actual routing of your belt to be sure your looking at the correct set-up, then mark the one that is exactly the same. If you re-route this belt incorrectly it can destroy the components it runs or if you miss a pulley it can destroy your engine. Personally, I take a pen to paper and draw my own rough (very rough, lol) diagram of the pulleys and route of the belt. Then I know for sure I have the correct route set-up. It may be helpful to view the video at this point because it demonstrates how to move the tensioner so you can pull the belt off. You place a socket on the tensioner, attach a breaker bar or similar leveraging bar and turn the spring loaded tensioner until there is enough slack that the belt will come off the pulleys. Then, gently release the tensioner back to its position.
  5. The nuts on the fan come off now. Use a long wrench or board to wedge between the fan and other nuts to hold the fan in place while you loosen each nut. Once loose you don't need the wedge any longer. Unscrew them the rest of the way by hand and set them somewhere safe, where they won't get lost. Pull the fan out and do the same thing with it. You don't want any of the blades bent. The pulley comes right off after the fan.
  6. Now you should be at the water pump. The bolts can be difficult to see because of their location. There are four of them, two on each side and they are over-under style (one above the other). A ratchet with an extension is your best choice here because the socket needs to go about five inches in to reach the bolts.
  7. Once the bolts are removed you may need to tap on the old water pump to get it free from the engine. Once its separated from the engine carefully lift it out so you don't damage your radiator with the front wheel on it and pull it out of the engine.

Install the New Water Pump

The mating surface (the point where the water pump meets the engine) must have all old gasket material, grease and grime removed. This is one of those things you really want to make sure you do well or the job was pointless, so let's do it right the first time!

  1. First, remove the four fan bolts from the old water pump and put them on the new water pump.
  2. The new water pump should have a new plug supplied with it, put this plug in the same spot it is on the old pump. If a new plug is not provided (unlikely, but can happen) remove the old plug. This can prove to be very difficult. Soak the old plug with "screw loose" or "WD 40" to loosen it up. You may even need to smack the heck out of the old pump to break that old plug loose. Yep, you may look like a raving lunatic smacking the old pump with a hammer, but just mention what you're doing and anyone that knows engines will understand! Now that you got that plug out of the old water pump, put it in the same spot on the new pump.
  3. Any other adapters old the old pump you should transfer to the new water pump.
  4. Using emery cloth, fine sandpaper (220 or higher) or a Dremel (use with caution, no gouging) clean the mating surface.
  5. When the mating surface is clean and dry prepare the new water pump for installation. It can be tricky mounting the pump while keeping the gaskets aligned and starting the bolts. The pump can be rather heavy, in an award position, with the gaskets slipping here and there. I have had a couple of failed installs because gaskets slipped, causing water to gush out and leaving me with a water pump to re-install, but not anymore. This is how I manage to do this part but whatever works for YOU then do that. Apply a thin line of gasket sealant to the pump mating surface. Set your gaskets on the sealant making sure to line up the holes in the gasket with the holes on the water pump. Apply another thin line of gasket sealant on the gaskets. Carefully slide the bolts through the holes and gasket and put some gasket sealant on the end of the bolt with the threads. Now your ready to mount the water pump.
  6. With bolts in place carefully lower the new water pump into position (if you have someone to help here would be nice) and start the bolts, by hand, into their respective holes being sure that the gaskets stay in place. Once you have them started in a few turns then you can put a socket to it.
  7. Once the bolts are snug but not tight, take out your torque wrench. Look up the torque specification in your shop manual and torque all four bolts. It should be somewhere between 20 foot lbs and 30 foot lbs.
  8. Connect the water pump hoses. This is a good time to replace any hoses showing signs of wear. Tighten the hose clamps.
  9. Set the pulley on the water pump wheel.
  10. Set the phone on the water pump wheel.
  11. Put the nuts back on to the bolts sticking through the fan holes. Snuggy them down using a leverage bar again.
  12. Referring to your chosen serpentine belt diagram, re-route your serpentine belt, then twist tensioner to put the final length of belt on.
  13. Replace the fan shroud.
  14. Close the draincock.
  15. Re-connect the battery negative cable.
  16. Fill radiator with radiator fluid. Burp the hoses by squeezing the large upper hose several times.
  17. While the radiator cap is still off, start the engine. Turn the heater on high/heat. The radiator is the direct source of heat for the inside of your vehicle. So you want to flow that system as well. Its a pretty cool little system heating the interior of vehicles so I included a photo of it. As the new pump starts working it will fill the system that was drained and you'll need to add coolant. Add coolant as needed until it stays full. Then replace the radiator cap.
  18. Get down and look for any leaks while its still running. Check the temperature gauge. It should remain at or below 2100 after the engine is warmed up (about 10 minutes at idle).

Leaks

If you see ANY leaking tear it down and do it again leaks WILL get worse and you have pride in your work so go back and do it again. 99% of the time it's those silly gaskets at the mounting surface that have moved that cause a leak or the torque is incorrect.

If there's not a leak in site congratulations!! YOU DID IT!! You're good to go for another 50,000 miles or more!

Thank you for reading,

Comments

Submit a Comment

  • Msmillar profile image
    Author

    Joanna 2 days ago from Valley Springs

    Was it helpful Joyce-Liang? When I'm writing I want to make sure that even someone that has little to no experience can perform the task. Thank you for reading!

  • Joyce-Liang profile image

    Joyce Liang 2 days ago from Zhengzhou

    This is really a detailed and useful instruction for water pump installation. ( by joyce from www.welpump.com)

Click to Rate This Article