ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

Degreasing your engine with pine-sol

Updated on November 11, 2013

Pine-sol: Easy and safe engine degreaser.

Any time you are working on a car you are likely to have dirty parts that you would like to clean. This can be easier said than done. I once spent 2 days cleaning a cylinder head with a towel and some Goop hand cleaner. Solvent sinks, ultrasonic cleaners, and sandblasting are common techniques used by professional shops for heavy duty degreasing, but a safer and easier way to clean your parts at home is to use pine-sol. Soak your parts in pine-sol overnight, wipe them off with a rag, and your parts will be sparkling clean.

Materials and Prep

To clean your parts with pine-sol, the first thing you need to do is prepare your parts to be cleaned. Pine-sol will remove paint and grease, soften carbon deposits on pistons and heads, and really soften the carbon inside an EGR system. Rubber seals and o-rings will be swollen for a while but after they dry out they do not seem to be harmed. Still, If I where planning to reuse any rubber parts I would make sure to remove them. Anything that might be harmed by the pine-sol that you want to keep intact should be removed. Ideally you should completely disassemble whatever you want to clean, but I have heard of people cleaning things like hydraulic lifters and just putting them right back in the engine head full of pine-sol to mix in with the oil. Needless to say, I don't think that is a good idea. Pine-sol contains a lot of water, after all. Once your parts are ready to be cleaned you will need to find a good container that they will fit in without requiring you to buy too much pine sol. In the case of the Geo Metro that I was working on when I wrote this article, I just used a big plastic bucket from wal-mart. In the case of larger engines like the VW I am restoring or my subaru outback, I find the smallest volume rubber-made container that I can fit the engine block into and use that for all the bigger parts, but most parts are cleaned in an old 1 gallon plastic ice cream tub. I buy a couple gallons of pine sol and dilute it as much as required to fill the container I am using. For the smaller parts I use Pinesol at full strength with a toothbrush before hand and then put them soak them for a while for a final cleaning.

Safety

Pine sol seems pretty innocus but it does require some safety precauctions. I would not go dipping my hands in it under most circumstances It does contain carcinogens. Also be aware that it can cause "temporary but very substantial" eye damage. I am not sure what that means and I am pretty sure I don't want to find out. In general you should probably where gloves whenever handling pinesol, which is something several people very familiar with pinesol have made clear to me time and time again. Anyway, be careful not to get it in your eyes, be aware that it might dry your skin, and read the label, and you should be all right. Its 100% safer than most other solvents you would use for this purpose.

A simple solution of pine sol and hot water for cleaning your parts

Ingredients

  • Pine Sol
  • Boiling Water

Instructions

  1. Use straight pine sol for small difficult to clean parts. For larger parts use a 50% or 75% dilution of hot water (The hotter the better). Mix the water and the pinesol togethor before adding your parts.
Cast your vote for Pine Sol mixture recipe
Degreasing my engine block with pine-sol
Degreasing my engine block with pine-sol

Cleaning your parts

Ready, Set, Dip!

When you remove your parts, you will want to let the pinesol drip off the them for a while. Hanging the parts over the pinesol container with a wire is a good idea just to let them drip off for a while. After most of the pinesol drips off, scrub the parts with a toothebrush and wipe them off with a clean towel and blow all the pine sol out of any internal holes with compressed air. You can actually wipe almost everything off of a part without using the toothbrush first, but I eventually got tired of wetting a toothbrush with fresh pinesol tor remove the tough grime all the time so I started just scrubbing the whole thing right at the beginning. I spend only a few seconds to a minute brushing each part but I am able to remove 99% of the grease, oil, and paint from most parts in that amount of time. If I still have trouble I just throw it back into the pinesol bath for another round. and it usually brushes of easily then. I use a stainles steel wire brush on extrememly tough deposits and I have not come into anything I could not remove with the combination yet.

Spray on

If you have a part you can't fit in a pine-sol bath, you can still use pine-sol to clean it. Just apply the pine-sol with a spray bottle and let it soak for a couple hours before scrubbing the surface and wiping it clean. Multiple applications may be required. This works well for large engine blocks, parts you don't want to remove, etc.. It is also popular for cleaning motorcycles in this form. You may have problems with flash rusting if you try to use this method. I would ignore it and use CLR afterwards in most cases, flash rusting is usually very superficial. This is akin to the way pine-sol has been used in households for years. Turns out it works pretty good on engines too. Who would have thunk it?

Tip

You can use Pine-Sol to clean grease stains out of your clothes and off of concrete also. It is also great for washing shop towels.

Buying your Pine-Sol

Where is the best place to buy pine-sol?

You can just run down to the hardware store and buy a gallon of pine-sol, but that will run you about $15.00, and if you need several gallons, that could be a problem. You can sometimes find pine-sol on sale, especially at bargain stores that sell unsuccessful or slightly damaged products at low prices. Be warned that while pine-sol brand is almost 1/4 pine oil, many knock off products are much less potent. Pine oil is the main ingredient so if you decide to buy an off brand make sure you are really getting more pine oil for your money. I bought one gallon at the hardware store and I am about to order more from amazon.

Pine-sol on Amazon

Pine-Sol Multi-Surface Cleaner, 60-Fluid Ounce Bottles (Pack of 6)
Pine-Sol Multi-Surface Cleaner, 60-Fluid Ounce Bottles (Pack of 6)

This 6 pack of 1 gallon pinesol bottles for only $32 costs about the same as two gallons at the hardware store with free shipping for amazon subscribers. This is the best deal for pinesol on amazon.

 

Rust Prevention

Don't let your parts rust!

100% pine-sol does not cause any rust in my experience, even if you let a thin film of it dry off your part. However, you will have to worry about your parts flash rusting as they dry if your pine-sol is watered down. I did not use enough Pine-Sol for my engine block and the cylinders ended up flash rusting. Probably not a huge problem, but I regret not wiping them down when I pulled the block out. Rust prevention is thankfully pretty simple. For complicated parts, a spray with oil like WD-40 is perfect but flat parts can just be wiped down with motor oil. Wiping the pine-sol off thoroughly will also do the trick. You should have have any problem avoiding your parts rusting, but be warned that they will if you do not take precautions to avoid it.

Let us know how pinesol worked on your clean up job.

Guestbook Comments

    0 of 8192 characters used
    Post Comment

    • profile image

      Brian 18 months ago

      Zep has a Pine cleaner, available at Home D3pot. It contains pine oil. looks a bit clearer than the new PineSol, but it contains pine oil. Soaking pistons right now to see how it works. And it is cheaper than PineSol.

    • profile image

      JD Olivier 2 years ago

      As of 2013, PineSol no longer contains any pine oil. Instead, it's mostly water, various alcohols, and a very strong acid, bringing the concentrated solution to a pH of ~2. The MSDS gives very different handling guidelines from those printed on the bottle.

    • Kailua-KonaGirl profile image

      June Parker 5 years ago from New York

      Degreasing engine parts with pine-sol is new to me, but then I don't work on cars. LOL. Sounds like a plan to me though since pine-sol works well on other cleaning chores.

    • Svdharma LM profile image
      Author

      Svdharma LM 5 years ago

      Like Geo Metros? Check out this lense! "Ten reasons to buy a Geo Metro"

    • profile image

      JoshK47 5 years ago

      Never heard of doing this before - thanks for sharing!

    • senditondown profile image

      Senditondown 5 years ago from US

      Pinesol is really powerful. Good hints for using it for engine parts.

    • profile image

      hope2012 5 years ago

      PS:

      I just tried using pinesol in my ultrasonic. It foamed a bit but it worked great.

    • profile image

      hope2012 5 years ago

      Hello,

      I found this page from your geometroforum.com. I'm to be rebuilding a honda xrf250. I tried using pinesol to clean up the valves. It worked very well. All I needed was a little wire brushing to get them clean. normally I spin them in the lathe. Only manual wire brushing was required this time.