ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

A Closet Turned Pegboard Tool Storage Idea

Updated on April 01, 2015
wilderness profile image

Dan has been a homeowner for some 40 years, and has nearly always done his own repair and improvement tasks. He is a licensed electrician.

A Pegboard Tool Storage Idea is Conceived

Recently my son and his new wife bought their first home and moved in with considerable excitement. Although he is not a great handyman, he was given a decent set of homeowner tools as a housewarming gift; the only problem was what to do with them? Where to keep them? The garage was chock full of moving "stuff" and when left in the house the children immediately found the toolboxes and emptied them. Tools all over the house!  A pegboard tool storage area would be nice, but there was no place to put it.

As with every new homeowner there were jobs that needed to be done that required the use of his new tools, but they were always lost and he spent more time searching for them than he did using them. Curtains needed hung, touch-up painting, maybe a new entrance door lock, but never the tools to work with.  Something had to be done.

His wife finally offered a long, narrow closet under the stairwell going upstairs. Such closets are usually quite deep, but only about three feet wide, and if filled it makes the rear of the closet impossible to get to. If we could turn that area into a pegboard tool storage area it would be perfect - a place for Dad's tools, while leaving the rear of the close still accessible for storage of seldom used items.


Hiltex 53106 Pegboard Hooks and Organizer Assortment | 50-Piece Variety Pack
Hiltex 53106 Pegboard Hooks and Organizer Assortment | 50-Piece Variety Pack

This is but one of many possible packages of pegboard hooks from Amazon. A word of caution, though - make sure the hooks you purchase are for the proper thickness of the pegboard. 1/8" hooks will not fit 1/4" pegboard, and the reverse is also true.

 

Planning the pegboard tool storage

My son had seen my workshop with some 20 feet of pegboard for hanging tools on and wanted something like it. He obviously didn't need that much pegboard, but some would be nice.

A toolbox of some kind would be necessary for tools that would not go on the pegboard, preferably a roll around type although they are usually quite expensive. It would not have to be top quality as it would never move from the closet, but needed to be of a fairly good size for a toolbox.

There was no light in the closet; if at all possible a light fixture needed to be added, as did a plug in for charging his cordless drill.


Attaching the pegboard

First on the agenda was to attach the pegboard. We made the decision to fit pegboard onto the right hand wall. That wall started out at about seven feet tall and tapered down to nothing at the far back of the closet, so the pegboard would also have to be tapered. Furring strips ¾" thick were purchased and nailed to the first first 3 studs in the area we wanted the pegboard to fit in. Each strip went from floor to ceiling, but we didn't bother to cut a perfect fit at the sloped ceiling as they would be covered anyway. Covering 3 studs would give some 4 feet of pegboard tool storage and seemed adequate.

We found three foot wide pegboard strips at a yard sale for a couple of dollars each and bought two 8' pieces. Carefully measuring the first piece we cut off the top at the same angle as the ceiling and nailed it to the furring strips with large head roofing nails. The width was cut at 32" so that the far edge fell on the center of a furring strip. The second piece was cut the same way, ending at the far edge of the remaining furring strip. As we began to hang tools the reason for the furring strips became apparent; the pegboard hooks need to protrude behind the pegboard and without the strips they cannot do so. We had purchased a variety of hooks, from straight to curved to one pair of small shelf brackets to mount a small shelf on the pegboard. The shelf brackets turned out to be a good idea as it makes a perfect place for the cordless drill and other small items.

Pegboard tool storage

pegboard installed
pegboard installed

The electrical work

We were fortunate enough that there was an electrical plug directly through the left hand wall (next to the proposed tool box) on the other side of the wall. A hole was cut into the sheetrock for an electrical "old work" box, and with the power turned off the existing plug in was removed and wire fed into it from the hole for the new plug. As we had made sure to cut the new hole in the same stud bay this was an easy task; we could reach in the new hole and touch the existing box.

One more hole was cut into the sheetrock near the ceiling for a "keyless" light fixture (a simple cheap ceramic fixture with a bare bulb and a pull chain to turn it on and off), again in the same stud bay. A more expensive fixture could be used, as could a switch for it, but it works well and cost only a couple of dollars. More wire was run from the new plug up to the light fixture and the boxes installed. The new outlet was installed into the box, as was the light fixture, with the final connections being made at the existing plug in. It turned out that the charger for the cordless drill would hang on the wall with a bracket and it was mounted near the door for easy reach and as a permanent mounting place. A cordless circular saw is planned as a future purchase; additional shelving will be added to the pegboard when it happens.

A small roll around tool box was found for under $100 and purchased for small tools that don't hang well and set into the closet. Tools were hung on the new pegboard tool storage - with time and experience their location will become fixed and the intent is to draw an outline around each tool. This way a glance tells the owner which one is missing and needs to be found.

Experience with the new pegboard tool storage idea has been very positive. Everything is easily found (at least if it's put away) and the rear half of the closet can still be used for storage of other items not often used. The total cost was well under $50 plus the tool box - a small price to pay for the convenience it offers.

New light fixture
New light fixture
Charger for cordless drill
Charger for cordless drill
There is still room at the back of the closet for storage
There is still room at the back of the closet for storage

Comments

    0 of 8192 characters used
    Post Comment

    No comments yet.

    Click to Rate This Article