ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

How To Build a Hydroponic Growing System Using Buckets To Grow Big Frosty Buds

Updated on August 4, 2012

Although this hydroponic grow setup is meant to accommodate four plants in five gallon buckets, you can simply adjust it to grow more or less plants if you decide to, and you can also use bigger or smaller containers. You can get most of the needed items at Lowe's, Home Depot, Target, Wal-Mart, K-Mart, Big lots etc. I bought them at Lowe's for about Two dollars a piece, and the 18 gallon Rubbermaid tote at Target for four bucks. The "T" connectors and tubing, I got at Home Depot. I also purchased the pump from Home Depot (in the section for gardening). The fountain pump was close to forty dollars. You can purchase a cheaper on which is fine but a larger one will make it easier to expand your hydroponic system later on down the road.

Please check that the pump has a filter that is removable otherwise you will have to make one to protect from debris. The majority of home improvement stores carry them somewhere within the store, and they can have them in more than one location. The throughholes/bulkhead fittings come in a lot of sizes and shapes. The ones that I used for this system I found at Lowe's for $2.

System Parts List

  • Four 5 Gallon Buckets
  • Four Through Holes/bulkhead fittings
  • Dark Vinyl (blue or black) Tubing (for fill and drain lines)
  • 1 Submersible Water Pump
  • 16 to 32 Gallon Tote Storage for the Reservoir
  • Cheap Timer (with a lot of on/off cycles)
  • Hydroponic Growing Medium (to support plants and to keep roots moist)
  • 1 Cheap Filter (to prevent growing medium from getting in the tubing)
  • Some “T” Connectors that Fit the Vinyl tubing your using (The total number depends on the final configuration)
  • A few Cans of cheap Black and White Spray Paint, (for light proofing the buckets and reservoir)
  • (Optional) A small amount of tubing and connectors for the return lines.

You will need to make sure the end of the through hole that the vinyl tubing will go on (end without the threads and nut), will fit the size tubing you are using. The ones I used will fit 5/8 inch inside diameter tubing. If not you can use two sizes of tubing and/or using a hose clamp to tighten it up. An old garden hose just might fit fine, and can be used instead of the vinyl tubing for the return lines.

Getting Started
First step is to trace the side of the through hole with the thread and nut, on the bottom of all 4, five gallon buckets. You’ll want it to be close to the edge of the bucket, but not so close you wont be able the thread the nut on in order to install it (about an inch). That’s so you will be able to set it upright on a table or bench, and most of the buckets weightwill still be supported and it wont tip over.

I use a rotary tool to make the holes, but if you don’t have one you can make the holes any way you want. Even a hot metal coat hanger will be able to melt the plastic nicely, then just scrape any burs off with a razor blade to make the edge soothe. It’s important that you don’t make the holes too big, or it may leak. It should be just big enough to stick the threaded side of the through hole in, without noticeable gaps. Now insert the through hole and tighten it up. Just make sure you have the rubber gasket on the right side. In most cases (depending on the particular through holes your using) it will most likely be on the outside of the bucket, and only the nut on the inside.

Now you’ll need to light proof the buckets. Turn them upside down, and put tape all around the through hole (so you don’t get paint on or in it). Give them a couple of coats of black spray paint, or as many as needed to block all the light. Then because the color black absorbs heat, give them a couple of coats of white spray paint. This will reflect light and help keep the root zone temperatures from getting hot. Make sure you only paint the outside, you don’t want paint to come in contact with the roots or nutrient solution.

The reservoir for your hydroponic system is quite simple, just paint the base and lid (outside) of the 18 to 30 gallon storage tote the same way you did the buckets. Painting it black to block light, and then white to reflect light. Once painted, cut a notch in the lid for the electric cord and hose from the pump to go through. Then another hole or two for the return line/s where you plan it to be.

Setting the system up
There are so many different configurations to setting up the hydroponic system, there’s no way to explain them all. The buckets can be setup on a table, bench, wall etc.. But the one thing that you need to be sure of is that the reservoir is at least 6 inches below. Otherwise the nutrient solution wont be able to flow back into the reservoir. The design is simple, the pump pumps the nutrient solution up to the top of the buckets, where it drips down through the bucket, and out the through hole at the bottom. Then the return tubing drains it back into the reservoir.

You can run the return lines different ways, but it should be a gentle slope all the way back to the reservoir. You can see that I connected the return lines from two buckets together with a “T” connecter, then back to the reservoir. The PVC at the end of the line’s going back into the reservoir is not necessary, although it does help keep the flow draining back more even. The tube coming out the side of the reservoir and looping back up through the center of the table, is the line that pumps up the nutrient solution from the pump to water the plants.

Getting the buckets ready to put the plants in is also quite simple, but just a few steps. First cut the filter part out of the furnace Filter, then cut a piece off to place over the through holes. This will keep the growing medium out of the tubing, but still allow the water to flow easily out the bottom. Now that you have the filter in place, place some rocks on top of that. I would fill about the bottom third with rocks. This holds the filter in place, and adds weight to the bucket keeping them firmly in place. (Note:) Be sure to clean and sanitize the rocks first by soaking them in bleach water for about an hour, then rinsing again. This reduces the chances of any root diseases.

On top of the rocks place the growing medium. I like coco chips myself, and that’s what I used when building this system. Coco chips and coco fiber are Basically the same thing, but the chips just larger partial sizes. Now make a loop using the vinyl tubing and a connecting “T” for all 4 buckets. These will be the dripper’s that will water the buckets. Once you have made them, take a paperclip and heat one end up with the flame of a candle, then poke some holes in the tubing ring with it. Notice that I cut a notch in the side of the buckets just large enough to hold the watering line in place snugly.

As with the drain lines, the feed (watering) line setup will depend on the configuration and positing of where you place your buckets. In this picture you can see how I have run the lines to my buckets. The feed line comes up through a hole in the center of the table. Then is split into 2 lines using a “T” connector, then each of those lines is split into two lines again using the same “T” connectors. Essentially splitting one feed line into 4 separate lines (one to each bucket).

I used a digital timer with this system (I already had it), but I later got another one for a different system for $5.95 at Walmart. It had plenty of settings and even a cover over the dial. For best results with the timer, make sure it ’s rated for 15 amps (usually called heavy duty). You will also want a timer that has pins for the on/off cycles all around the dial, not just a few (for analog timers). That’s because it will need to be turned on and off many times during the day. Digital timers usually have many on/off cycles that can be set. 

Of course you can buy a hydroponic grow kit, but what is the fun in that.  Ok OK, I know, but by building your own hydroponics system you have the ability to make it fulfill all your growing needs and then some.

Happy Growing!


    0 of 8192 characters used
    Post Comment

    • Phil The Gain profile imageAUTHOR

      Phil The Gain 

      6 years ago from Planet Earth

      Whiteflies are attracted to yellow objects, so put some yellow-sticky traps on the tops of pots among the plants. Adult flies can be sucked from underside of leaves with a low powered vacuum cleaner,early in the light cycle when whiteflies are cold and slow moving. You can also shake plants and suck adults out of the air.They are easily eradicated with natural sprays such as an insecticidal soap applied at 5-10 day intervals. I'm not keen on using sprays during flowering but if you're still in the early part of the floral cycle, foliar misting with water after killing whiteflies will help remove any residual soap. Put oscillating fan on to keep whiteflies disturbed so sticky-traps are more effective.

    • Druid Dude profile image

      Druid Dude 

      7 years ago from West Coast

      Cool hubs. Too paranoid myself. Conditioned response. No card yet, but, ooooh I'm in PAIN!!! White flies. Best way to combat white flies. Flat out starting over. Any tips?


    This website uses cookies

    As a user in the EEA, your approval is needed on a few things. To provide a better website experience, uses cookies (and other similar technologies) and may collect, process, and share personal data. Please choose which areas of our service you consent to our doing so.

    For more information on managing or withdrawing consents and how we handle data, visit our Privacy Policy at:

    Show Details
    HubPages Device IDThis is used to identify particular browsers or devices when the access the service, and is used for security reasons.
    LoginThis is necessary to sign in to the HubPages Service.
    Google RecaptchaThis is used to prevent bots and spam. (Privacy Policy)
    AkismetThis is used to detect comment spam. (Privacy Policy)
    HubPages Google AnalyticsThis is used to provide data on traffic to our website, all personally identifyable data is anonymized. (Privacy Policy)
    HubPages Traffic PixelThis is used to collect data on traffic to articles and other pages on our site. Unless you are signed in to a HubPages account, all personally identifiable information is anonymized.
    Amazon Web ServicesThis is a cloud services platform that we used to host our service. (Privacy Policy)
    CloudflareThis is a cloud CDN service that we use to efficiently deliver files required for our service to operate such as javascript, cascading style sheets, images, and videos. (Privacy Policy)
    Google Hosted LibrariesJavascript software libraries such as jQuery are loaded at endpoints on the or domains, for performance and efficiency reasons. (Privacy Policy)
    Google Custom SearchThis is feature allows you to search the site. (Privacy Policy)
    Google MapsSome articles have Google Maps embedded in them. (Privacy Policy)
    Google ChartsThis is used to display charts and graphs on articles and the author center. (Privacy Policy)
    Google AdSense Host APIThis service allows you to sign up for or associate a Google AdSense account with HubPages, so that you can earn money from ads on your articles. No data is shared unless you engage with this feature. (Privacy Policy)
    Google YouTubeSome articles have YouTube videos embedded in them. (Privacy Policy)
    VimeoSome articles have Vimeo videos embedded in them. (Privacy Policy)
    PaypalThis is used for a registered author who enrolls in the HubPages Earnings program and requests to be paid via PayPal. No data is shared with Paypal unless you engage with this feature. (Privacy Policy)
    Facebook LoginYou can use this to streamline signing up for, or signing in to your Hubpages account. No data is shared with Facebook unless you engage with this feature. (Privacy Policy)
    MavenThis supports the Maven widget and search functionality. (Privacy Policy)
    Google AdSenseThis is an ad network. (Privacy Policy)
    Google DoubleClickGoogle provides ad serving technology and runs an ad network. (Privacy Policy)
    Index ExchangeThis is an ad network. (Privacy Policy)
    SovrnThis is an ad network. (Privacy Policy)
    Facebook AdsThis is an ad network. (Privacy Policy)
    Amazon Unified Ad MarketplaceThis is an ad network. (Privacy Policy)
    AppNexusThis is an ad network. (Privacy Policy)
    OpenxThis is an ad network. (Privacy Policy)
    Rubicon ProjectThis is an ad network. (Privacy Policy)
    TripleLiftThis is an ad network. (Privacy Policy)
    Say MediaWe partner with Say Media to deliver ad campaigns on our sites. (Privacy Policy)
    Remarketing PixelsWe may use remarketing pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to advertise the HubPages Service to people that have visited our sites.
    Conversion Tracking PixelsWe may use conversion tracking pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to identify when an advertisement has successfully resulted in the desired action, such as signing up for the HubPages Service or publishing an article on the HubPages Service.
    Author Google AnalyticsThis is used to provide traffic data and reports to the authors of articles on the HubPages Service. (Privacy Policy)
    ComscoreComScore is a media measurement and analytics company providing marketing data and analytics to enterprises, media and advertising agencies, and publishers. Non-consent will result in ComScore only processing obfuscated personal data. (Privacy Policy)
    Amazon Tracking PixelSome articles display amazon products as part of the Amazon Affiliate program, this pixel provides traffic statistics for those products (Privacy Policy)