ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

Carpet/Floor Finishers orHow to Install a Multi-Level Threshold

Updated on April 7, 2018
Baselines
Baselines | Source

How to install a Multi-Level Threshold


Why would I need this?

If you have ever changed flooring from carpeting in one room to wood or laminate in another, or opened up a room by removing a wall and have a transition from a tile floor to a carpeted area, you may have considered using a threshold. When working on older home or even just for aesthetics, a threshold gives a more finished look.

We didn’t plan on changing our floors, but we had to widen the door to the kitchen to get a new refrigerator and range to fit through. The kitchen door was a pocket door, so when we widened the door, we realized the rest of the wall wasn’t stable so we removed the wall completely. We were then left looking at a rough edge of carpet and kitchen tiles. We decided that the area would have to have a threshold to cover the transition for looks as well as safety.

There are many thresholds. Some are just flat pieces that mark the end of one room or area and helps transition to another. Needing a threshold that is going from one height to another is a little trickier.

HOW LONG WILL THIS TAKE

· 4 hours (uninterrupted and with tools)

HELPFUL HINTS

· We chose a metal threshold by M-D Building Products. Their product was good and fairly easy to install.

· Seeing a picture, reading the steps and thinking the installation through should save you time and grief.

· Be a good trouble shooter. Different contractors install different type of subflooring or install it in different ways, so think this through. You might even want to draw a picture if you are a visual person.

· It is a good idea that you trim any uneven edge’s from your carpet before you begin. Why? Because you don’t want to get to the end and see part of your carpet fraying out from the threshold because it was too short to be covered properly.

Tools:

· A straight edge – any ruler, yardstick, piece of lumber, etc., that is flat and straight.

· a tape measure,

· a razor knife to cut carpet,

· a tri-square,

· a jigsaw,

· a drill and a ¼” bit,

· a hammer and a nail,

· a metal file,

· Two clamps,

· Two short pieces of 2x4,

· M-D Multi-Floor Transition Threshold (with Cherry Finish).

PREP THE FLOOR

Step 1. Lay down the threshold and get it in the proper location.

· Once in place, carefully draw a line along the threshold edge on the hard floor side using a soft lead pencil (#2). This will become your “baseline guide.”

· It is a good idea to also draw a line on the opposite side of the threshold onto the carpet just to give you a visual of where the threshold will end and how much carpet you may have to cut back to allow a clean drill hole for your retainers.



Measuring the groove
Measuring the groove
Mark the carpet
Mark the carpet
measuring
measuring
cutting to size
cutting to size
Tri-square for marking drill holes
Tri-square for marking drill holes
Line up retainers
Line up retainers
Now you are finished!!!
Now you are finished!!!

Sept 2: Determine where to drill the ¼” Holes;

· Turn the threshold upside down.

· Measure from the edge of the threshold to the center of the groove on the bottom.

Sept 3: Repeat step 2 and mark where the rest of your drill holes will go.

· Evenly space out the remaining drill hole marks.

Sept 4: Using the nail as a punch

· Gently hammer it through the carpet at each dot mark until you feel it begin to go into the wooden subfloor.

  • You want to hammer it in enough to make a clean, clear mark in the subfloor under the carpet so you will know where to drill after the carpet is cut back.
  • I decided that I would cut out notches in the carpet where the nail hole marks were located
  • Drilling holes through carpet is not a great idea because you may pull or tear the carpet.

PREP THE THRESHOLD

What do I do if the threshold is not the length I need?

· The M-D threshold I chose comes in 6 ft. and 3 ft. lengths.

· You need to measure the distance to be covered by the threshold.

· You may need to cut a piece to add to another piece for a large opening.

HELPFUL HINT

· If you are not good at using a tape measure, you could use a length of string.

  • Secure it at one end and then mark where the string meets the opposite “wall”
  • Mark this distance off on the threshold.
  • ·Be sure that when you draw your cut line that it is straight.
  • Cutting the Threshold

In my case, the distance was greater than 6 feet. I needed 8 feet 8 inches. I needed to combine the 6’ and 3’ pieces to get my 8’8”. Of course, that is 9 ft., so then I had to cut the short piece for the correct length.

If that is you situation here is how you do it.

· Step 1: Place the short threshold in position using your baseline as a guide.

· Step 2: Place the longer threshold in place (again using your base line guide) so that one end is placed over the short threshold.

· Step 3: Using your #2 pencil draw a line over the short threshold to mark where the longer threshold ends.

HELPFUL HINT:

· If you have butted each end of your threshold against your walls properly, and the edges are in line with the base line, the mark you draw on top of the short threshold should be even and square.

· Step 4: Place the short threshold on top of two pieces of 2 x 4.

  • Be sure to leave a 2 inch gap between the 2x4’s
  • This will allow the jig saw blade enough height and width to cleanly cut through the metal threshold.
  • Use a sheet metal cutting blade in the jig saw

· Step 5: Clamp down the threshold tight enough so it won’t move when being cut.

HELPFUL HINT

  • This cut can be made without using the clamps and 2X4’s, but you will need someone to helphold the threshold down.

DO NOT TRY THIS BY YOURSELF!

If you slip you may hurt yourself

Use a sheet metal cutting blade in the jig saw

Put the threshold on the edge of a table with the end to be cut sticking out over the edge.

It is very important that your cut be smooth, clean and straight! If it is, when you place the cut piece on the floor it should butt up to the longer piece and be almost invisible.

· Once the cuts are made to the threshold, put them in place on the floor to make sure they fit properly. If the cut edges do not fit smoothly, use the metal file to remove any burrs or rough edges.

DRILLING THE HOLES

At this point you need to prep the carpet so you can drill the holes for your threshold retainers. As said earlier, I decided to cut out notches in the carpet where my holes would be. I did this because I wanted as much carpet as possible under the threshold to avoid any problems in the future.

· Step 1. Put a ¼ “drill bit in your drill.

· Step 2. Drill a hole through the subfloor at each of the spots where your nail punch marks are.

· Step 3. Clean each drill hole to remove dust or splinters

INSTALL THE THRESHOLD

  • · Step 1. With your threshold setting vertically on the carpet, slide the threshold retainers into the middle groove of the threshold.
  • · Step 2. Align the retainers to match the location of each hole.
  • · Step 3. Carefully slide the threshold retainer tips up to and in to the drill holes as you turn the threshold up into its normal position.
  • · Step 4. With the retainer tips setting in each hole, gently tap them in place by tapping the top of the threshold with your hammer.

HELPFUL HINT

Place a block of wood or some other material between the hammer and the top of the threshold to prevent scaring or marking up the top of the threshold when you hit it with the hammer.

· Step 5. Once the retainers are firmly in place, use your hammer and drive them down until the threshold is firmly against the floor and carpet.

CONGRATULATIONS!! YOU NOW HAVE A NEW NICE LOOKING THRESHOLD



Comments

    0 of 8192 characters used
    Post Comment

    No comments yet.

    working

    This website uses cookies

    As a user in the EEA, your approval is needed on a few things. To provide a better website experience, hubpages.com uses cookies (and other similar technologies) and may collect, process, and share personal data. Please choose which areas of our service you consent to our doing so.

    For more information on managing or withdrawing consents and how we handle data, visit our Privacy Policy at: https://hubpages.com/privacy-policy#gdpr

    Show Details
    Necessary
    HubPages Device IDThis is used to identify particular browsers or devices when the access the service, and is used for security reasons.
    LoginThis is necessary to sign in to the HubPages Service.
    Google RecaptchaThis is used to prevent bots and spam. (Privacy Policy)
    AkismetThis is used to detect comment spam. (Privacy Policy)
    HubPages Google AnalyticsThis is used to provide data on traffic to our website, all personally identifyable data is anonymized. (Privacy Policy)
    HubPages Traffic PixelThis is used to collect data on traffic to articles and other pages on our site. Unless you are signed in to a HubPages account, all personally identifiable information is anonymized.
    Amazon Web ServicesThis is a cloud services platform that we used to host our service. (Privacy Policy)
    CloudflareThis is a cloud CDN service that we use to efficiently deliver files required for our service to operate such as javascript, cascading style sheets, images, and videos. (Privacy Policy)
    Google Hosted LibrariesJavascript software libraries such as jQuery are loaded at endpoints on the googleapis.com or gstatic.com domains, for performance and efficiency reasons. (Privacy Policy)
    Features
    Google Custom SearchThis is feature allows you to search the site. (Privacy Policy)
    Google MapsSome articles have Google Maps embedded in them. (Privacy Policy)
    Google ChartsThis is used to display charts and graphs on articles and the author center. (Privacy Policy)
    Google AdSense Host APIThis service allows you to sign up for or associate a Google AdSense account with HubPages, so that you can earn money from ads on your articles. No data is shared unless you engage with this feature. (Privacy Policy)
    Google YouTubeSome articles have YouTube videos embedded in them. (Privacy Policy)
    VimeoSome articles have Vimeo videos embedded in them. (Privacy Policy)
    PaypalThis is used for a registered author who enrolls in the HubPages Earnings program and requests to be paid via PayPal. No data is shared with Paypal unless you engage with this feature. (Privacy Policy)
    Facebook LoginYou can use this to streamline signing up for, or signing in to your Hubpages account. No data is shared with Facebook unless you engage with this feature. (Privacy Policy)
    MavenThis supports the Maven widget and search functionality. (Privacy Policy)
    Marketing
    Google AdSenseThis is an ad network. (Privacy Policy)
    Google DoubleClickGoogle provides ad serving technology and runs an ad network. (Privacy Policy)
    Index ExchangeThis is an ad network. (Privacy Policy)
    SovrnThis is an ad network. (Privacy Policy)
    Facebook AdsThis is an ad network. (Privacy Policy)
    Amazon Unified Ad MarketplaceThis is an ad network. (Privacy Policy)
    AppNexusThis is an ad network. (Privacy Policy)
    OpenxThis is an ad network. (Privacy Policy)
    Rubicon ProjectThis is an ad network. (Privacy Policy)
    TripleLiftThis is an ad network. (Privacy Policy)
    Say MediaWe partner with Say Media to deliver ad campaigns on our sites. (Privacy Policy)
    Remarketing PixelsWe may use remarketing pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to advertise the HubPages Service to people that have visited our sites.
    Conversion Tracking PixelsWe may use conversion tracking pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to identify when an advertisement has successfully resulted in the desired action, such as signing up for the HubPages Service or publishing an article on the HubPages Service.
    Statistics
    Author Google AnalyticsThis is used to provide traffic data and reports to the authors of articles on the HubPages Service. (Privacy Policy)
    ComscoreComScore is a media measurement and analytics company providing marketing data and analytics to enterprises, media and advertising agencies, and publishers. Non-consent will result in ComScore only processing obfuscated personal data. (Privacy Policy)
    Amazon Tracking PixelSome articles display amazon products as part of the Amazon Affiliate program, this pixel provides traffic statistics for those products (Privacy Policy)