ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel
  • »
  • Sports and Recreation»
  • Hiking & Camping

How To Repair or Replace Airstream Travel Trailer Leveling Jacks

Updated on May 20, 2013
Randy Godwin profile image

Randy is a lifelong lover of the outdoors and especially camping. This article is intended to help the RVer save money and time on repairs.


How To Replace Airstream Leveling Jacks

Owners of Airstream travel trailers know they can depend on these well built RV’s for a lifetime of enjoying the outdoors and traveling across America.  But as the years roll on, even these classic camping units need some maintenance and repairs.  Like any high end product, the repairs can run into quite a bit of expense unless you are a hands-on type person.  

This article shows how to replace the leveling jacks on an 1986 Airstream 31 ft. Sovereign travel trailer.  Although the jacks would possibly last for many years or even the lifetime of the unit, there are cases in which they need to be replaced.  Many models of older Airstream travel trailers used similar leveling jacks.  

Forgetting to raise one or more of the leveling jacks will result to damage to the jack in most cases.  Leaving the jack lowered or raised while in an area close to the ocean can cause it to rust and malfunction.  Whatever the reason, eventually one or more of the leveling jacks will need to be replaced.

A Classic !954 Airstream Globe Trotter
A Classic !954 Airstream Globe Trotter | Source

Off With The Old Jacks

1986 Airstream Sovereign 31 Ft.
1986 Airstream Sovereign 31 Ft.
Badly corroded leveling jack
Badly corroded leveling jack
Removing the old leveling jacks
Removing the old leveling jacks

Removing Old Jacks

What should be a relatively easy job of unbolting the old leveling jacks and installing the new ones unfortunately does not always turn out this way.

In most cases, there will be some of the bolts which refuse to budge.

They will either break off into the steel beam they are attached to, or the edges of the hex will round off leaving the bolt still attached.

I ran into both scenarios while installing the four new leveling jacks to the Airstream Sovereign and on older models where the Airstream jack stands are original equipment.

Obviously, this is a common occurrence for Airstream travel trailers as the new leveling jacks had offset holes which allowed drilling new holes in a different location on the support beams.

The jacks fit in the same spot but used new holes to support the new leveling jacks. Make sure there are obstructions if moving to a slightly different spot for the new jack stands.

It was actually easier if the bolt broke off in the beam as only a little grinding was required to level the area where the leveling jacks fit against the bottom of the beam.

Otherwise, the entire head of the bolt had to be ground off with a side grinder. The use of a cutting torch is not recommended because of the close proximity of the aluminum skin covering the bottom of the unit.

Be very careful so as not to scratch the exterior metal covering any time you are working around it.

Completing the New Jack Installation

Damage to aluminum beneath old jacks
Damage to aluminum beneath old jacks
Attaching new leveling jacks
Attaching new leveling jacks
Completed replacement of new leveling jack
Completed replacement of new leveling jack
Good as new and good to go!
Good as new and good to go!

Installing the New Airstream Leveling Jacks

Often the aluminum skin beneath the leveling jack attachment area is corroded or even absent because of the contact between steel and aluminum metals.

Now is the time to make sure it doesn’t get any worse by patching it before installing the new leveling jacks. There are several methods to ensure the deterioration doesn't get worse.

I used an aluminum backed rubber adhesive roofing repair product sold at Lowe’s or Home Depot building supply stores, but other materials and sealants will do just fine.

After cutting a strip of the repair product to fit the attachment point of the jack, I raised the jack until it was firmly pressed into the correct position against the bottom of the unit.

This allowed new holes to be drilled without fear of the leveling jack moving. A high quality bit is needed as this is hard steel.

Run self tapping bolts into the new holes until they are snug but not tight. Check for proper placement and a firm fit before removing the bolts and applying a thread locking substance to the bolt threads.

You may now tighten the bolts as much as desired for the final step in replacing the leveling jacks. Torque these bolts snugly but don't overdo it.

Airstream accessories are often expensive to purchase but are worth it for some aspects of safety and durability.

Be sure to examine aftermarket replacement Airstream parts well before using them on your Airstream travel trailer.

Enjoy your vintage Airstream and keep your investment in good shape for many years to come by keeping it in tip top shape and using good replacement parts during repairs.


    0 of 8192 characters used
    Post Comment

    • Randy Godwin profile image

      Randy Godwin 7 years ago from Southern Georgia

      Yes they can, Fox. Coating the jack threads with a good quality grease should be done each year. The new jacks come already coated with grease on the threads. Thanks!

    • profile image

      Fox Jones 7 years ago


      Can older slightly rusty jacks be oiled or greased in the meantime to free them up a bit and make it easier to turn? Or would that compromise the stability of the jack?

      - fox