ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel
  • »
  • Sports and Recreation»
  • Hiking & Camping

RV Tire Covers, Get Rid of the Bungee Straps

Updated on December 26, 2017
Don Bobbitt profile image

Don has been an avid traveler and motorhome owner for most of his life and shares his experiences with valuable tips.

An Installed RV Tire Cover

A properly installed RV Tire Cover should look like this, nicely fitted.
A properly installed RV Tire Cover should look like this, nicely fitted. | Source

RV Tire Covers are a necessity for Campers

There are a lot of things an RV owner learns they need to do to protect their camper in some way.

As we all know, RV tires, like al other vehicle tires degrade over time and the biggest culprit that ages your tires is exposure to the Sun.

Even though tire manufacturers state that their tires will meet their design specifications for at least 5 years before they should be replaced due to degradation.

But, if you read the fine print, this five year limit assumes what they call “normal” wear and tear, which includes typical exposures to the Sun.

With this in mind you will see that most RV owners will place tire covers over their tires when storing their RV, and most will even use tire covers when they are staying in a campground for several days or more.

Problems Installing and removing RV Tire Covers

But, I have one big problem with these tire covers. Sure, they’re fitted and it does take a few minutes, standing in an awkward position to fit the cover over the tires.

This is mostly due to the fact that tires are made using rubber, and rubber is not a slick material that other materials will easily slide over.

So, at times, you can end up in a tugging match just getting your tire covers properly installed on your tires.

Then, once you do get the cover in place, there is an attached bungee strap that you must deal with.

The purpose of the bungee is to keep the tire cover from flying off of the tire and disappearing into the campground.

Popular RV Tire Cover

ADCO 3952 White Ultra Tyre Gard Wheel Cover
ADCO 3952 White Ultra Tyre Gard Wheel Cover

Probably the most popular brand of Tire covers for RV's, I purchased my new set of white covers almost two years ago. They fit perfectly and they are easily cleaned.


The Bungee Strap Process is horrible

Getting this Bungee they provide attached properly can turn into a real task at times, for some campers.

At first glance, the process looks simple. There are two brass-lined holes in the back edge of the tire cover, and all you have to do is pull the bungee through the two holes and attach it to itself.

Oh, did I mention that the positions of these two holes are on the backside of the tire? Yep, that’s right, this is one of those tasks that requires you to get your arms and hands behind the tire and then fiddling with the bungee ends until it is laced through the two holes and then tied to itself.

Now, here is my problem; I am 69 years old and I am not some nubile gymnast that can bend my body into different positions anytime I want. Nope, I an Old, and stiff and it takes me a while just to get down onto my knees.

The very thought of the contortions required to hug my very large tires and installing a tire cover, or removing one for that matter, sends my worn out lower back into sympathetic spasms before I even start.

Oh, and of course, you need to install, and eventually remove, one of these covers for each outer tire on your RV.

That means at last four times you have to get onto your knees, and go through this painful process. In case you haven’t noticed, I loath the fact that I have to use tire covers.

Redefine the Problem before you look for a solution

Being such a “baby”, if you want to call me such, I have put a lot of thought into this Tire Cover process and I have devised a much more humane way to install my Tire Covers.

The first thing I did was sit down and define the real problem.

The real problem is that these tire covers are open in the back and really have nothing to hold them onto the tire when the wind gets to blowing around in a campground or storage area.

So, if the rear of the cover is not contained in some way, the gusting wild can eventually blow the tire cover off of the tire. After all, the tire cover is just a lightweight piece of vinyl with a soft interior lining that is, again, open on the backside of the tire.

I figured that i could deal with installing the tire cover, because this step of the process is relatively easy after you get the hang of it.

But, I needed to get rid of this whole bungee strap and the need to wrestle with tying the backside corners of the tire cover to each other.

Think ing this over some more, I realized that what I needed to do was keep the back corners of the standard tire cover from being blown open from the tire itself when the winds got heavy.

Simple parts to modify Tire Covers

The tire covers and the parts I used to modify mine so that I didn't need to use the bungee straps.
The tire covers and the parts I used to modify mine so that I didn't need to use the bungee straps. | Source

Weights, not Bungee Straps

Then it hit me, if all I needed to do was keep the backside corners of the covers from “flapping” in the wind, what was needed was a way to put weights on the backside corners.

Perfect! I had a solution, weights on the corners of the cover. Then I went through a long list of potential weights that pretty much any camper could get and attach to the tire covers.

Whatever weights I used had to be; 1- just heavy enough to hold the corners down, 2- cheap, and they had to be 3- easy to attach.

So, I ended up with a three dollar roll of good carpenters line and eight, two ounce or heavier fishing sinkers as a kit. See the attached photo.

All you need to do is cut pieces if carpenters line into eight ten-inch lengths. I found that if the string are too long, they will often tend to get tangled up on things on the ground.

You just tie one end of the string to each sinker, then you tie the other end to the brass eyelets on the corners of the tire covers, the same eyelets designed for the bungee strap. See the attached photo.

Once you have installed the sinker weights onto the tire covers, you simply slide the cover over the tire, as you normally would and then you reach around and flip the sinkers behind the tire. I use my awning hook for this so I don't have to bend over.

The sinkers keep the ends of the backside of the tire covers from being blown around by the wind and they stay firmly in place.

And, when you are ready to pull out, a few tugs on the cover will pull it off of the tire with the sinker weights dragging along to the outside of the tire.

Then it a simple process of rolling up the tire covers, with sinkers attached, and stuffing them into your RV storage area for use the next time.

by Don Bobbitt, August, 2015

Tire Cover Weights installed

Weights installed on the eyelets of a standard RV Tire Cover.
Weights installed on the eyelets of a standard RV Tire Cover. | Source

Make your own RV Tire Covers

© 2015 Don Bobbitt


    0 of 8192 characters used
    Post Comment

    • Don Bobbitt profile image

      Don Bobbitt 7 months ago from Ruskin Florida

      A good idea 62morgan

    • profile image

      62morgan 7 months ago

      I simply pre-secure or "Close" the bungee cord "before" installing. Pull cover down across the face of tire, all the while slipping the bungee cord down the rear of the tire. This slip-on technique grips it nicely. Job Done!

      Cover is too long. I fold approx. 6 inches up at bottom and tug it for final fit to leave vinyl approx. 1-1.5 inches off pavement.

    • Don Bobbitt profile image

      Don Bobbitt 2 years ago from Ruskin Florida

      metal1- I understand, a four years ago, we went west and hung around the area from Apache Junction up to Flagstaff for several months.

      I ended up going to a fishing tackle store and purchasing some weights that are heavier.

      At some point, you will get enough weight that even if one end comes off, the weights keep them from going anywhere.

      I have found over the past several years, that here on the east coast, lighter weight does the job for me.

      You can't design something for every contingency, just the most likely.

      Thanks for the read and the comment.


    • profile image

      metal1 2 years ago

      tried the weights on the back side of the covers but the wind here in the high desert still took the covers for a few hundred yard flight.we found them but still need to find a better way to hold them in place. you are very correct the way the factory holds them on is also impossible for a handycapable person to install , a buddy with a service related amputation could not get them in place

    • teaches12345 profile image

      Dianna Mendez 2 years ago

      I don't own a motor home but I'm sure those who do will find this very useful. Interesting to read how it's done.

    • profile image

      Jinpak 2 years ago

      Great post.. Read here