ArtsAutosBooksBusinessEducationEntertainmentFamilyFashionFoodGamesGenderHealthHolidaysHomeHubPagesPersonal FinancePetsPoliticsReligionSportsTechnologyTravel

Fly Tying - Tube Popper Fly

Updated on May 27, 2014

Tubes for a Popper Fishing Fly?

Tube fishing flies are tied using a plastic tube instead of the hook shank, then a fishing line is passed through the tube and a hook attached directly to the fishing line.

Advantages of Tube Fishing Flies are:

  • Hook size and style (this includes treble hooks) can be changed as desired using the same tube fishing fly pattern.
  • Tend to last longer than traditional fishing flies since tube fishing flies typically slide up the line and away from the fish's teeth.
  • Shorter hook shanks make tube fishing flies less prone to being thrown by the fish when fighting one.

With this in mind, would tubes work for a Popper Fishing Fly?

Tubes Work!

After some tinkering around with various balsa popper bodies and hook sizes, tubes work for a Popper Fishing Fly! For want of a name to call the fishing fly, simple seems best... the end result is the Tube Popper Fly.

Replacing the fur and feathers of a Tube Fishing Fly with a balsa popper body the Tube Popper Fly capitalizes on the Tube Fishing Fly's advantages! Recent fishing trips using a Tube Popper Fly, the following were noted:

  • Hook size can be changed while using the same popper body, allowing more flexibility to adjust to short striking fish. Moreover, if smaller fish (or larger fish) are the norm for a given outing, the hook size can be changed as well.
  • Since the hook and the popper body are not permanently attached, damage to the popper body is minimized when fighting a hooked fish.
  • The shorter hook shank provide a more solid hook set as well as the fish is less likely to gain leverage against the hook and is more likely to stay hooked! The key was finding the right size hook!

For more on tying a Tube Popper Fly, check out the sections below, and do give this pattern a try!

Note: The Tube Popper Fly is not a replacement to the traditional Popper Fishing Fly. Instead, it is another pattern in the fly box that can be called upon when needed.

Materials (less the hooks)
Materials (less the hooks)

Materials

The following is the material list for the Tube Popper Fly:

  1. 3/4" x 3/4" X 1-1/2" to 2" Balsa Wood (width x height x length)
  2. Pearl Flashabou
  3. Fish Eyes of your choice
  4. Plastic Tube Small (we used Size 6 Copper Wire and stripped the plastic cover)
  5. Plastic Tube Large (we used Size 12 Copper Wire and stripped the plastic cover)
  6. Hook with eye that will fit inside Large Plastic Tube (we used a Size 2 Wacky Worm Hook but suggest a Size 6 Treble Hook as a starting point)
  7. Zap-A-Gap or Superglue
  8. 5" Epoxy or Hard As Nails Polish
  9. Colored Sharpie of your choice

Mini Balsa Wood Lathe
Mini Balsa Wood Lathe

Suggested Tools

Although shaping can be done by hand, we found the Mini Balsa Wood Lathe made for easier and more accurate shaping of the balsa wood popper bodies.

Do check out the partner article - Simple Mini Balsa Wood Lathe, for more details on making one!

Also, other suggested tools include:

  1. Xacto Miter Saw and Box for cutting the balsa wood to length
  2. Small Dremel Bit for hollowing the popper body's front
  3. Small Drill Bit for boring out the popper body where the tube will be inserted
  4. Drying Wheel to slowly turn the popper body while the epoxy (or nail polish) dries

Note: These are suggested tools and can be readily substituted with other tools as needed.

Click thumbnail to view full-size
Cutting to LengthBalsa Wood Cut to Length
Cutting to Length
Cutting to Length
Balsa Wood Cut to Length
Balsa Wood Cut to Length

Step 1

Cut the Balsa Wood to length. For the fishing fly in this article, the Balsa Wood was cut to 1-1/2" in length.

This was based on the typical size bait fish in a local pond frequented by the author.

Although not required, an Xacto Miter Box and Saw were used to cut the Balsa Wood. These can be readily substituted by other tools.

Click thumbnail to view full-size
Balsa Wood centered on Mini Balsa Wood Lathe in preparation for turning.Balsa Wood shaped and ready for the next step.Balsa Wood Popper Body
Balsa Wood centered on Mini Balsa Wood Lathe in preparation for turning.
Balsa Wood centered on Mini Balsa Wood Lathe in preparation for turning.
Balsa Wood shaped and ready for the next step.
Balsa Wood shaped and ready for the next step.
Balsa Wood Popper Body
Balsa Wood Popper Body

Step 2

Next, sand the Balsa Wood into the desired shape you would like.

For this article, a cone shape was decided upon and a Mini Balsa Wood Lathe was used to turn the wood down to its final shape.

Other suggested tools include a Dremel Tool, a small Hand Drill, or a Sanding Block. All can be used to shape and turn the Balsa Wood to its final shape.


Click thumbnail to view full-size
Small Drill Bit for boring out the Balsa Popper BodyBoring out the Balsa Popper BodyBalsa Popper Body drilled through centers (back view)Balsa Popper Body drilled through centers (front view)
Small Drill Bit for boring out the Balsa Popper Body
Small Drill Bit for boring out the Balsa Popper Body
Boring out the Balsa Popper Body
Boring out the Balsa Popper Body
Balsa Popper Body drilled through centers (back view)
Balsa Popper Body drilled through centers (back view)
Balsa Popper Body drilled through centers (front view)
Balsa Popper Body drilled through centers (front view)

Step 3

In Step 3, the Balsa Popper Body is bored through the body's center which will later serve to guide the Tube through the popper body.

Using a small Drill Bit, slowly drill through the wood from front to back.

Since the popper body is easily damaged at this point, it is strongly suggested to do this by hand.

Click thumbnail to view full-size
Small Dremel Bit to hollow Popper Body's frontPopper Body's front is completed
Small Dremel Bit to hollow Popper Body's front
Small Dremel Bit to hollow Popper Body's front
Popper Body's front is completed
Popper Body's front is completed

Step 4

Next, in Step 4, the Balsa Popper Body's front is hollowed out to make a concave surface.

The concave surface results in the fish enticing gurgling/popping sound when the Tube Popper Fly is retrieved in short "jerks" of the line!

Using a small Dremel Bit (see picture in the sidebar), begin hollowing out the popper body's front face.

Hollow out the front face until a 1/8" deep concave depression is formed.

Note: It is also strongly suggested to do this by hand for the same reasons noted in the previous step. A slight slip of the bit could result in damage and lost work!


Click thumbnail to view full-size
Size 6 and Size 12 Copper Wire (used in place of Plastic Tubes)Wires Stripped and ready for gluing.Small Tube inserted into the Popper Body and glued in place.Large Tube inserted over Small Tube and glued in placeZap-A-Gap used to glue Tubes in place.Ready for the next step!
Size 6 and Size 12 Copper Wire (used in place of Plastic Tubes)
Size 6 and Size 12 Copper Wire (used in place of Plastic Tubes)
Wires Stripped and ready for gluing.
Wires Stripped and ready for gluing.
Small Tube inserted into the Popper Body and glued in place.
Small Tube inserted into the Popper Body and glued in place.
Large Tube inserted over Small Tube and glued in place
Large Tube inserted over Small Tube and glued in place
Zap-A-Gap used to glue Tubes in place.
Zap-A-Gap used to glue Tubes in place.
Ready for the next step!
Ready for the next step!

Step 5

In Step 5, the Tubes are cut to length, and then glued in place using Zap-A-Gap:

  • Since Copper Wire was used in place of Plastic Tubes used for Tube Fishing Flies, the wires are stripped and the copper removed.
  • Next, cut the Tubes to length. The Small Tube will run the length of the popper body and extend out the back approximately 1/8". The Large Tube is cut to 1/4". (Note: 1/4" was added to the Small Tube and extended out the front; this was used later to hold the popper body in the fly tying vise).
  • Then, coat the Small Tube with Zap-A-Gap and insert it into the popper body. Be sure the Small Tube extends out the back.
  • With the Small Tube in place, glue to Large Tube to the Small Tube that extends out the back using Zap-A-Gap.
  • Be sure to keep the Small Tube clear of glue. If necessary, insert a piece of monofilament line into the Small Tube to ensure the tube remains clear.

Note: Copper Wire was used for the Tubes as Plastic Tubes were not available at the time. In "working with what I had", Copper Wire was readily available. However, it is strongly suggested to use traditional Plastic Tubes or the Plastic Tubes from Q-Tips as a more economical alternative.

Click thumbnail to view full-size
"Paint" the popper body.Apply the Fish EyesCoat with 5" Epoxy (or several coats of Nail Polish)
"Paint" the popper body.
"Paint" the popper body.
Apply the Fish Eyes
Apply the Fish Eyes
Coat with 5" Epoxy (or several coats of Nail Polish)
Coat with 5" Epoxy (or several coats of Nail Polish)

Step 6

Step 6 prepares the Balsa Popper Body for painting and final finishing - specifically:

  • Using a colored Sharpie, "paint" the popper body.
  • Then, apply the Fish Eyes; use Super Glue to hold them in place,
  • And then, following the directions on the Epoxy container, mix the epoxy and apply a coat to the popper body.
  • If nail polish is used, apply it and let dry between coats. Use about three coats of nail polish.
  • If you have a Drying Wheel, set the popper body on the wheel and let dry. Else, slowly turn the popper body by hand until the epoxy sets.

Note: The Small Tube was cut a 1/4" longer than required; the extra 1/4" section was extended out the front of the popper body to be used as a holding point when secured to the Fly Tying Vise. Another means of doing this, uses a toothpick inserted in the Small Tube from the front.

Click thumbnail to view full-size

Step 7

In Step 7 - the final step, the Flashabou and Hackle are applied:

  • First, secure the popper body in the vise as shown in the sidebar. If an extra 1/4" was not added to the Small Tube, insert a toothpick into the Small Tube from the front of the popper body, and then secure it to the vise.
  • Next, form a tail using the Pearl Flashabou and secure it to the Large Tube. Cut the tail so it is slightly shorter than half the popper body's length.
  • Then, secure the Grizzly Hackle to the end of the Large Tube, use a Palmer Wrap to work the hackle forward, and stop just short of the popper body.
  • Finally, work the tying thread through the hackle and toward the popper body, stop just short of the popper body, and use several wraps to secure the hackle.
  • Finish the Tube Popper Fly using a whip finish knot, cut the thread, apply head cement to the wraps, and let dry.

Once the head cement is dry, the Tube Popper Fly is ready to fish!

Note: Do check out the pictures of finished Tube Popper Flies below as well as the Suggested Fishing Tips section for more on fishing with them!

Tube Popper Flies

Click thumbnail to view full-size
Tube Popper Fly with a Dressed HookTube Popper Fly using a Size 2 Wacky Rig Worm HookTube Popper Fly with "Fish Eyes" and a Size 10 Treble HookIf one is good, why not two Tube Popper Flies!Quick switch of hooks, same Tube Popper Fly but now with a Size 2 Wacky Rig Worm Hook.
Tube Popper Fly with a Dressed Hook
Tube Popper Fly with a Dressed Hook
Tube Popper Fly using a Size 2 Wacky Rig Worm Hook
Tube Popper Fly using a Size 2 Wacky Rig Worm Hook
Tube Popper Fly with "Fish Eyes" and a Size 10 Treble Hook
Tube Popper Fly with "Fish Eyes" and a Size 10 Treble Hook
If one is good, why not two Tube Popper Flies!
If one is good, why not two Tube Popper Flies!
Quick switch of hooks, same Tube Popper Fly but now with a Size 2 Wacky Rig Worm Hook.
Quick switch of hooks, same Tube Popper Fly but now with a Size 2 Wacky Rig Worm Hook.

Reader Poll

Do Tube Fishing Flies work better than Traditional Fishing Flies for the same pattern?

See results

Suggested Fishing Tips

When fishing a Tube Popper Fly, here are a few suggestions:

  • After casting the Tube Popper Fly, let the fishing fly sit undisturbed. As a general rule, don't retrieve it until you see the rings that formed when the fishing fly landed on the water dissipate. (If at night, count to ten before retrieving).
  • When retrieving the fishing fly, start using two long pulls on the fly line to simulate an injured bait fish thrashing on the surface or a grasshopper struggling in the water. Pause for a 2-6 count delay, and then retrieve again.
  • If Bass are actively chasing bait fish, then try using short pulls on the fly line and forego the pause. Often times, you will see the Bass trailing behind the fishing fly!
  • If you are missing hook sets, change the size or type of hook you are using. As a rule of thumb, a size 6 treble hook is a good starting point when fishing for Bass.

Good Luck and Good Fishing!

PS: Do check out the videos below to see the Tube Popper Fly in action!

Comments

    0 of 8192 characters used
    Post Comment

    • hbng84 profile imageAUTHOR

      hbng84 

      4 years ago

      Do give this one a try next chance to get; has worked out well in our area!

    working

    This website uses cookies

    As a user in the EEA, your approval is needed on a few things. To provide a better website experience, hubpages.com uses cookies (and other similar technologies) and may collect, process, and share personal data. Please choose which areas of our service you consent to our doing so.

    For more information on managing or withdrawing consents and how we handle data, visit our Privacy Policy at: https://hubpages.com/privacy-policy#gdpr

    Show Details
    Necessary
    HubPages Device IDThis is used to identify particular browsers or devices when the access the service, and is used for security reasons.
    LoginThis is necessary to sign in to the HubPages Service.
    Google RecaptchaThis is used to prevent bots and spam. (Privacy Policy)
    AkismetThis is used to detect comment spam. (Privacy Policy)
    HubPages Google AnalyticsThis is used to provide data on traffic to our website, all personally identifyable data is anonymized. (Privacy Policy)
    HubPages Traffic PixelThis is used to collect data on traffic to articles and other pages on our site. Unless you are signed in to a HubPages account, all personally identifiable information is anonymized.
    Amazon Web ServicesThis is a cloud services platform that we used to host our service. (Privacy Policy)
    CloudflareThis is a cloud CDN service that we use to efficiently deliver files required for our service to operate such as javascript, cascading style sheets, images, and videos. (Privacy Policy)
    Google Hosted LibrariesJavascript software libraries such as jQuery are loaded at endpoints on the googleapis.com or gstatic.com domains, for performance and efficiency reasons. (Privacy Policy)
    Features
    Google Custom SearchThis is feature allows you to search the site. (Privacy Policy)
    Google MapsSome articles have Google Maps embedded in them. (Privacy Policy)
    Google ChartsThis is used to display charts and graphs on articles and the author center. (Privacy Policy)
    Google AdSense Host APIThis service allows you to sign up for or associate a Google AdSense account with HubPages, so that you can earn money from ads on your articles. No data is shared unless you engage with this feature. (Privacy Policy)
    Google YouTubeSome articles have YouTube videos embedded in them. (Privacy Policy)
    VimeoSome articles have Vimeo videos embedded in them. (Privacy Policy)
    PaypalThis is used for a registered author who enrolls in the HubPages Earnings program and requests to be paid via PayPal. No data is shared with Paypal unless you engage with this feature. (Privacy Policy)
    Facebook LoginYou can use this to streamline signing up for, or signing in to your Hubpages account. No data is shared with Facebook unless you engage with this feature. (Privacy Policy)
    MavenThis supports the Maven widget and search functionality. (Privacy Policy)
    Marketing
    Google AdSenseThis is an ad network. (Privacy Policy)
    Google DoubleClickGoogle provides ad serving technology and runs an ad network. (Privacy Policy)
    Index ExchangeThis is an ad network. (Privacy Policy)
    SovrnThis is an ad network. (Privacy Policy)
    Facebook AdsThis is an ad network. (Privacy Policy)
    Amazon Unified Ad MarketplaceThis is an ad network. (Privacy Policy)
    AppNexusThis is an ad network. (Privacy Policy)
    OpenxThis is an ad network. (Privacy Policy)
    Rubicon ProjectThis is an ad network. (Privacy Policy)
    TripleLiftThis is an ad network. (Privacy Policy)
    Say MediaWe partner with Say Media to deliver ad campaigns on our sites. (Privacy Policy)
    Remarketing PixelsWe may use remarketing pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to advertise the HubPages Service to people that have visited our sites.
    Conversion Tracking PixelsWe may use conversion tracking pixels from advertising networks such as Google AdWords, Bing Ads, and Facebook in order to identify when an advertisement has successfully resulted in the desired action, such as signing up for the HubPages Service or publishing an article on the HubPages Service.
    Statistics
    Author Google AnalyticsThis is used to provide traffic data and reports to the authors of articles on the HubPages Service. (Privacy Policy)
    ComscoreComScore is a media measurement and analytics company providing marketing data and analytics to enterprises, media and advertising agencies, and publishers. Non-consent will result in ComScore only processing obfuscated personal data. (Privacy Policy)
    Amazon Tracking PixelSome articles display amazon products as part of the Amazon Affiliate program, this pixel provides traffic statistics for those products (Privacy Policy)