How to Restore iPhone 4 Using Redsnow and shsh Blobs
If you have the shsh blobs stored with Cydia servers, you can downgrade or upgrade iPhone firmware using Redsnow.
iPhone restore via iTunes is meant to happen smoothly but can be marred with plenty of errors since Apple’s authentication and verification procedures are a little complex and any hiccup during the restore process causes iTunes to generate errors.
It is also no secret that iPhone firmware restore in old iPhones can cause its own share of headaches, more so if the firmware to be restored is no longer signed. When Apple stops signing IOS firmware, restoration will not happen unless shsh blobs are used.
You can also restore iPhone firmware without iTunes, using Redsnow. Redsnow can query, submit and fetch shsh blobs, making it a better option and is capable of downgrading IOS firmware in your iPhone.
If you get nervy about doing firmware restore using iTunes, then Redsnow is probably your best option.
As far as I know, iPhone 4 firmware restore via Redsnow will go smoothly and tend to take shorter times.
What is shsh Blobs?
Shsh, short for Signature HaSH, is actually the signature data from Apple servers which is used to identify and ultimately approve installation of IOS firmware in your iDevice. IOS firmware restore cannot take place without availability of shsh blobs. You must upload or have iDevice shshs blobs saved locally on your computer. This can be done via Redsnow or Tiny Umbrella.
Cydia servers have been designed to mimic Apple servers, and unlike Apple which only permits saving of the latest blobs for a device, Cydia saves older blobs, thus allowing restore of older IOS firmware.
How to Save iPhone shsh Blobs
In order to save your shsh blobs with Cydia, put your iPhone in DFU mode and simply click Fetch in Redsnow.
The process will be done in a short while and your files will be available remotely.
In order to find out what shsh blobs have been uploaded remotely, just click on the Query tab and within a short while, you should see a list of them. (see image below)
You can also save the shsh blobs in your computer if you so wish.
How to Restore iPhone 4 Firmware 6.0.1 Using Redsnow
For this demonstration, we shall use an iPhone 4 to restore firmware 6.0.1 up from 5.1.1, using Redsnow 0.9.15b3.
You should also have IOS versions 6.0.1 and 6.0 downloaded in your computer. IOS 6.0 will mainly apply for jailbreakers and those that wish to preserve iPhone baseband, when running Recovery Fix.
- The first thing is to power up Redsnow as computer Administrator.
- You will be presented with two tabs: Jailbreak and Extras.
- How To Enter DFU Mode In Your iPod Or iPhone
DFU mode stands for Device Firmware Mode, meaning pre IOS boot state in the iPod or iPhone commonly refered to as iBoot. DFU mode is a requirement if you intend to upgrade or downgrade iPhone firmware.
- Click Extras and you should see more tab options in the next window.
- The last tab in the new window is named Even More.
- Click on it.
- You will then be served another window.
- Click on the fist tab named Restore. The Restore option enables Redsnow to install new firmware in your iPhone by using remotely saved shsh blobs or blobs saved locally on the computer.
- In the next window, click the tab IPSW and point to the iPhone 4 firmware 6.0.1 which you want restored.
- Redsnow may probably pop up a warning about not recognizing the IPSW but will allow you to continue.
- If you are a jailbreaker and/or probably want to prevent baseband upgrade you may want to select YES.
- If however your iPhone is factory unlocked you may pick any of the two choices.
- Upon making your choice, Redsnow will get busy identifying and fetching your shsh blobs from remote Cydia servers.
- Redsnow will automatically attempt to put your iPhone in Recovery mode.
- You may also opt to put your iPhone in DFU mode in case Redsnow prompts you to.
- Most often than not however, Redsnow will handle all business for you.
- The restore process will get moving and this should not last more than just a few minutes.
- You should now see the white Apple logo and a filling bar on the iPhone.
- When the bar fills up, the iPhone will reboot.
- Now, depending on how you configured the iPhone baseband option above, two scenarios will unfold.
- If you chose not to preserve your baseband - that is if your iPhone is factory unlocked, your iPhone should reboot normally.
- If however you chose to preserve your iPhone baseband, your phone will reboot to a screen displaying the iTunes logo and usb cable.
- If the latter is your situation, do not worry, for you have two ways out of this
- First, you can boot up fully by jailbreaking your iPhone.
- If you are not into jailbreaking however, you could simply use the Recovery Fix feature in Redsnow.
- How To Download And Install Old Apps For iPhone 3G and 3GS And IOS 4x And 3x
In order to download and install old apps for iPhone 3G and 3GS which usually run IOS 4X and lower, you need to fiddle around with a few tweaks in order to get the job done. Of course you must have jailbroken your iPhone to start with. You will have
Using the Recovery Fix to boot your iPhone
- First open Redsnow as Administrator and select the Extras tab.
- The next window will have a selection of tabs.
- First click on the fifth tab Select IPSW tab and point to the IOS 6.0.1 firmware. If Redsnow fails to identify 6.0.1, you should now point to IOS 6.0. do not get scared. This will simply help boot up your iPhone. It will not change the firmware from 6.0.1 to 6.0.
- Now click on the third tab named Recovery Fix.
- Redsnow will prompt you to put your iPhone in DFU mode.
- If you are not good with DFU mode, simply press the POWER and HOME on the iPhone button until it is completely off and press Next.
- Redsnow will give you step by step instructions on how to enter DFU mode.
- If properly done your iPhone should now reboot and display the RAM disk image and finally the running Apple man!
- If you own a factory unlocked iPhone, follow the instructions on the screen and you should reach the home screen in no time.
- For unlockers however, you will first have to jailbreak your iPhone.